User manual JBL SDP 5

[. . . ] Manufactured under license from Dolby Laboratories. "Dolby, " "Pro Logic, " "Surround EX, " and the double-D symbol are trademarks of Dolby Laboratories. Manufactured under license from Lucasfilm Ltd. Lucasfilm and THX are trademarks or registered trademarks of Lucasfilm Ltd. [. . . ] A 16:9 display device (widescreen) is connected to an S-video output connector. Controls the appearance of the on-screen display when the display device is connected to an S-video output connector. When set to ON, the display device shows the on-screen display in a 4:3 aspect ratio* regardless of the incoming signal. When set to OFF, the display device shows the on-screen display in the same aspect ratio as the input signal. * Aspect ratio refers to the size of the picture on the display device screen or to the size of the display device screen. A 16:9 aspect ratio, often referred to as "widescreen, " is almost twice as wide as high. 3-22 SDP-5 SETUP MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS INPUT SETUP DVD1 DVD2 SAT VCR TV CD TUNER AUX DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL +0dB VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH L7 FILM %!D 5. 1 L7 FILM DTS-ES DTS-ES L7 FILM MAIN ADVANCED ZONE2 IN DIGITAL DVD1 MAIN ADV INPUT SELECT DIGITAL 2-CH ANLG BYP OFF S-VIDEO 16:9 AUTO S-VIDEO OSD 4:3 ON COMPONENT OSD OFF ON OFF The DVD1 INPUT SETUP menu is shown here as an example, and will continue to be shown as an example throughout this section. Whenever it appears, any other INPUT SETUP menu may be substituted. Likewise, whenever the DVD1 input appears as a step in a menu path, any other input may be substituted. COMPONENT OSD SETUP INPUTS DVD1 MAIN ADVANCED COMPONENT OSD ON, OFF Controls the appearance of the on-screen display when the display device is connected to the component video output connector. When set to ON, the display device shows the on-screen display as a 480i video signal on a full blue-screen background. To minimize viewing distractions, the two-line status does not appear on the on-screen display. When set to OFF, the display device does not show the on-screen display, including the two-line status (2-18). Note: When the ON-SCREEN DISPLAY menu BACKGROUND parameter (3-51) is set to OFF, the display device using the component video output connector will not show the on-screen display. 3-23 SETUP ZONE2 IN SETUP INPUTS DVD1 ZONE2 IN JBL Synthesis DIGITAL, ANLG, DMIX Controls the interaction of the digital and analog audio input connectors assigned to the selected Zone 2 input. The INPUT SETUP menu can be used to assign one digital and one analog audio input connector for the selected input. Refer to pages 3-7 and 3-8 for more information. The table shown on the next page describes ZONE2 IN parameter settings. MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS INPUT SETUP DVD1 DVD2 SAT VCR TV CD TUNER AUX DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL +0dB VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CH L7 FILM %!D 5. 1 L7 FILM DTS-ES DTS-ES L7 FILM MAIN ADVANCED ZONE2 IN DIGITAL DIGITAL ANLG DMIX The DVD1 INPUT SETUP menu is shown here as an example, and will continue to be shown as an example throughout this section. Whenever it appears, any other INPUT SETUP menu may be substituted. Likewise, whenever the DVD1 input appears as a step in a menu path, any other input may be substituted. CAUTION When the ZONE2 IN parameter is set to DIGITAL or ANLG, the SDP-5 recognizes some dts-encoded input sources as audio signals (not data signals) and outputs loud digital noise from the Zone 2 audio output connectors. 3-24 SDP-5 SETUP ZONE2 IN Parameter Settings The table below describes ZONE2 IN parameter settings. DIGITAL The SDP-5 automatically sets the ZONE2 IN parameter to DIGITAL when the ANALOG IN parameter is set to NONE. · The SDP-5 sends the assigned digital audio input connector to the Zone 2 audio output connectors. The SDP-5 ignores the assigned analog audio input connector. Independent zone monitoring is available. The DIGITAL IN parameter (3-7) can be used to assign a digital audio input connector for the selected input. ANLG (Analog) DMIX (Downmix) · · The SDP-5 automatically sets the Set the ZONE2 IN parameter to DMIX to send a downmixed version of ZONE2 IN parameter to ANLG Main Zone audio to the Zone 2 audio output connectors. Downmixes when the DIGITAL IN parameter can be generated for Dolby Digital and dts(-ES) sources. · To generate a downmix, the same input must be selected in the · The SDP-5 sends the Main Zone and Zone 2. Otherwise, the Zone 2 audio output assigned analog audio input connectors will mute. connector to the Zone 2 · Main Zone listening mode activation affects the Zone 2 audio audio output connectors. [. . . ] Default parameter settings differ from input to input. The MAIN ADV menu shown above indicates the default parameter settings for the DVD1 input. The MAIN ADV menus shown on page 3-17 indicate default parameter settings for each input. DVD1 DTS-ES MODE DTS-ES L7 FILM DTS-ES L7 MUSIC DTS-ES THX DTS-ES DTS-ES 2-CHAN USE LAST A-7 Appendix Menu Tree (continued from page A-7) MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION R 80Hz C 80Hz M SUB 80Hz 80Hz L SL 80Hz RL 80Hz SR 80Hz RR 80Hz JBL Selecting a SPEAKER SETUP menu option opens the corresponding menu shown below and at the right (e. g. selecting the CUSTOM SETUP option opens the CUSTOM SETUP menu shown below). LEVELS CALIBRATION INTERNAL NOISE TEST DACS CALIBRATION BASS PEAK LIMITER continued on page A-9 SPEAKER DISTANCES FRONT LEFT 0. 0ft CENTER 0. 0ft FRONT RIGHT 0. 0ft SIDE RIGHT 0. 0ft REAR RIGHT 0. 0ft REAR LEFT 0. 0ft SIDE LEFT 0. 0ft SUBWOOFER 0. 0ft UNITS FEET FEET METERS 0. 0 to 30. 0ft SYNTHESIS 7CH SETUP !CAUTION! [. . . ]