User manual JBL SPYROWCHEU

[. . . ] Use extreme caution when cutting or drilling in and around these areas. · Before drilling or cutting holes, use a utility knife to remove unwanted fabric or vinyl to keep material from snagging in a drill bit. · When routing cables, keep input-signal cables away from power cables and speaker wires. · When making connections, make certain they are secure and properly insulated. [. . . ] If your source unit does not have a remote turn-on connection, connect the amplifier's (REM) terminal to the vehicle's accessory circuit. Speaker Connections Refer to the application guides on the pages that follow. Speaker connections should be made using a minimum of 16-gauge wire. High-Level Input Connections The GTO75. 2 II, GTO75. 4 II and GTO755. 6 II amplifiers are equipped with speaker-level inputs that allow you to add an amplifier to head units that do not have RCA line outputs. The speaker outputs for the source unit should be connected to the amplifier using the supplied connector (square four-wire plug). The GTO301. 1II, GTO601. 1II and GTO1201. 1II amplifiers are not equipped with high-level inputs. NOTE: When using the high-level inputs, the AUX outputs can be used to pass a line-level signal to another amplifier. Wire Gauge Chart Amplifier Maximum Minimum Model Current Draw Wire Gauge 34A #8 AWG GTO75. 2 II 85A #8 AWG GTO75. 4 II GTO755. 6 II 87A #8 AWG 40A #8 AWG GTO301. 1II 69A #6 AWG GTO601. 1II GTO1201. 1II 115A #4 AWG These recommendations assume 7' ­ 10' wire runs. If your installation differs markedly, you will need to adjust the wire gauge accordingly. IMPORTANT NOTE: If you are planning to use optional neon tubes, install them before making any electrical connections to the amplifier (refer to"Installing Neon Tubes" on page 6). Figure 1. Terminal connection end plate. GTO75. 2 II 2 APPLICATIONS ­ GTO301. 1 II, GTO601. 1 II AND GTO1201. 1 II The GTO subwoofer amplifiers are single-channel amplifiers. 6-Channel operation: GTO755. 6 II amplifier driving full-range front and rear speakers and a pair of subwoofers. Subwoofer ­ + Rear Right ­ + Front Right ­ + GTO755. 6 II (partial end panel) ­ + ­ + Rear Left Front Left Figure 10. 5-Channel operation: The same as Figure 9, with the subwoofer output bridged to drive a single 4-ohm subwoofer, providing the speaker with more power. Subwoofer ­ + Right ­ + Left + ­ GTO755. 6 II (partial end panel) Figure 11. 3-Channel operation: GTO755. 6 II amplifier configured for 3-channel operation, where all of the channels are bridged for a subwoofer and a pair of component speakers. 5 INSTALLATION AND SETUP SETTING THE CROSSOVER(S) Determine your system plans and set the crossover mode switch accordingly. If you plan to use the GTO75. 2 II or GTO75. 4 II to drive full-range speakers, set the crossover mode to FLAT and skip to "Setting Input Sensitivity. " Initially set the crossover frequency control midway. While listening to music, adjust the crossover for the least perceived distortion from the speakers, allowing them to reproduce as much bass as possible. Systems using a separate subwoofer set the crossover mode to HP (high pass) for your full-range speakers. Adjust the crossover frequency to limit bass and provide increased system volume with less distortion. For subwoofers, choose the highest frequency that removes vocal information from the sound of the subwoofer. If using the GTO75. 2 II or GTO75. 4 II to drive a subwoofer(s), set the crossover mode to LP (low pass). NOTE: The GTO301. 1II, GTO601. 1II, GTO1201. 1II and the subwoofer output of the GTO755. 6 II are low-pass only and do not have a crossover mode switch. Initially turn the INPUT LEVEL control(s) to minimum (counter clockwise). [. . . ] Using a 3 /32-inch Allen wrench, remove only the screws on the amplifier's (top) clear cover and set them aside. Remove the end panel and slide the cover off. Locate the enclosed hardware bag and remove the four clips. Each clip has a square end and a larger round end. [. . . ]