User manual JBL TAKE CONTROL TC1000

[. . . ] *X03-76009* Take Control Information in this document is subject to change without notice. The names of companies, products, people, characters, and/or data mentioned herein are fictitious and are in no way intended to represent any real individual, company, product, or event, unless otherwise noted. Complying with all applicable copyright laws is the responsibility of the user. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Microsoft Corporation. [. . . ] 4 In the Buttons list, select the appropriate button and drag it to the Macro editor. 5 Repeat steps 3 and 4 to finish building your macro, and then click Done. Notes l When using macros, your devices may require a moment to respond, requiring you to include a short delay between steps. If your device does not respond correctly when you first use a macro, try adjusting the Delay setting, beginning with the lowest setting, and then increasing it, as needed. See the TC1000 Online User's Guide for more information. l You can add about 30 macros. Getting Help If you would like additional information on using the Take Control software, refer to the extensive TC1000 Online User's Guide, which contains detailed information on all aspects of the TC1000 software. To access the TC1000 Online User's Guide, click Help in the Take Control Editor. 19 Take Control Feature Summary This summary identifies features that you can perform directly on your Take Control unit and those that require use of a computer and the Take Control software. Take Control Only Page 6 Page 7 Page 9 Page 10 Page 11 Page 11 Page 12 Page 12 Page 13 Page 4 Page 10 ­ ­ Page 10 ­ ­ Take Control with Software Page 14 Page 18 Page 18 Page 18 ­ ­ ­ ­ ­ ­ Page 17 Page 18 Page 18 Page 18 Page 18 Page 19 Feature Set up the TC1000 Learn IR code from a device's remote control Add a device Delete a device Calibrate the touchscreen Set the contrast Set the time Turn the speaker on or off Adjust the display time-out Reset the TC1000 settings Create a new activity Customize an activity Add a button to a device Delete a button from a device Customize a button Create and edit macros 20 Harman Kardon Troubleshooting If you have difficulty with your Take Control unit, consult the following problem descriptions for a quick solution. If you continue to have difficulties, see the "Technical Support" section within this manual for further direction. Cause The batteries are low in either the TC1000, the remote control you are trying to learn, or both. Solution Replace the batteries, as needed. For the TC1000, see "Replacing the Batteries, " page 28. For the remote control, see the documentation for the remote control. Cause The system controller is in direct sunlight or under fluorescent lighting. Solution Direct sunlight or fluorescent lighting may cause interference with the IR signal from the system controller. Use it away from direct sunlight or fluorescent lighting. Cause The electronic device may have IR frequencies that are incompatible with Take Control. Solution Please contact us at the number in "Technical Support, " page 29. Cause There may be other IR-controlled devices in the room, creating a conflict with the TC1000 IR signal. Solution Turn off or refrain from using other IR-controlled devices. Cause The button on the remote control being learned does not work or is set to an alternate-device mode, such as VCR when you are trying to learn a TV button. Solution Before learning the button on the remote control, verify that it works properly by pressing the button and observing a correct response on the device. Setup I received a message "Code not learned. [. . . ] Should you have any questions, or if you desire to contact Harman for any reason, write: Harman Customer Service 250 Crossways Park West Woodbury, NY 11797 C LIMITED WARRANTY Warranty Period Harman warrants that the on the day you receive and for the next 90 days for the SOFTWARE and on the day your receive and for the next one (1) year thereafter for the Remote Control Device, and under normal use and service, (a) the SOFTWARE will perform substantially in accordance with the accompanying packaging and documentation, and (b) the Remote Control Device accompanying the SOFTWARE will be substantially free from defects in materials and workmanship. Who Is Protected By This Warranty Your Harman warranty protects you, the first licensed user of the SOFTWARE and Remote Control Device, provided that the Harman Remote Control product and accompanying SOFTWARE was purchased from an authorized dealer, and there are no third-party beneficiaries of this Limited Warranty. A copy of the original dated sales receipt must be provided whenever warranty service is required. Please attach a copy of your sales receipt to this warranty and put it in a safe place. What Is Covered Your Harman warranty covers all defects in material and workmanship with the following specified exceptions. These are: (1) damage caused by accident, unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims must be presented to the carrier); (3) damage to or deterioration of any accessory or decorative surface; (4) damage resulting from failure to follow instructions contained in your user's manual; (5) damage resulting from the performance of repairs by someone other than an authorized Harman warranty station; (6) damage caused by the installation of parts that do not conform to Harman specifications; (7) any Harman unit on which the serial number has been effaced, modified, or removed; (8) units used for other than home use. [. . . ]