User manual JBL UREI 535

[. . . ] Never spill liquid of any kind on the product. The apparatus shall not be exposed to dripping or splashing, and no objects filled with liquids, such as vases, shall be placed on the apparatus. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. [. . . ] It enables us to keep you posted on our latest advancements, and helps us to better understand our customers and build products that meet their needs and expectations. JBL Consumer Products INCLUDED Each model sold separately CSC55 CSS10 Grille CST55 (2) Wall brackets CSB5 Grille Grille (1) Wall bracket 3 SPEAKER PLACEMENT FRONT SPEAKERS CENTER CHANNEL SPEAKER 0­2 ft 0­0. 6m SUBWOOFER SURROUND SPEAKERS Single surround back speaker may be used with 6. 1 receivers and processors. Alternate placement for surround speakers when only 5. 1 channels are used; required placement for surround back speakers in 7. 1-channel systems. The front speakers should be placed the same distance from each other as they are from the listening position. The CSB5 speakers should be placed at about the same height from the floor as the listeners' ears will be, or they may be angled toward the listeners. The center channel speaker should be placed slightly behind the front left and right speakers, and no more than 2 feet (0. 6m) above or below the tweeters of the left and right speakers. It is often convenient to set the center speaker on top of the television set, as shown in the drawing. The JBL Cinema Sound speaker system may be used in 5. 1-, 6. 1- or 7. 1-channel applications. In 5. 1-channel applications, two of the surround speakers should be 4 placed slightly behind the listening position and, ideally, should face each other and be at a level higher than the listeners' ears. If that is not possible, they may be placed against a wall behind the listening position, facing forward. In 6. 1-channel applications, two of the surround speakers should be placed in the side positions, and a single surround back speaker should be placed against the wall behind the listening position. In 7. 1-channel applications, place two of the surround speakers in the side positions, and place the two surround back speakers against the rear wall. In Dolby® Digital and DTS® systems, it is best to aim all of the speakers (except the subwoofer) toward the listening position at or slightly above about ear-level height. In systems where only analog surround processing (such as Dolby Pro Logic® II) is available, it may be preferable to aim the speakers straight out from the wall to obtain a more diffuse sound. To comply with European CE certification, these holes are blocked with plastic inserts at the point of manufacture. To use banana-type connectors requires the removal of the inserts. The hole in the center of each collar is intended for use with banana-type connectors. To comply with European CE certification, these holes are blocked with plastic inserts at the point of manufacture. To use banana-type connectors requires the removal of the inserts. 6 DOLBY® DIGITAL OR DTS® (OR OTHER DIGITAL SURROUND MODE) CONNECTION RECEIVER SUBWOOFER L R LFE OUT LINE LFE LEVEL IN Use this installation method for Dolby Digital, DTS or other digital surround processors: Use the line-level input jack marked "LFE" for the LowFrequency Effects channel. Connect this jack to the LFE output or subwoofer output on your receiver or amplifier. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier. Make sure that you have configured your surround sound processor for "Subwoofer On. " Also configure your receiver for 5. 1-, 6. 1- or 7. 1-channel operation as appropriate. The front left, front right, center and rear speakers should all be set to "Small. " If your receiver allows you to set the crossover frequency between the subwoofer and the main speakers, select 100Hz or the setting that is the closest frequency below it. DOLBY PRO LOGIC® (NON-DIGITAL) ­ LINE LEVEL Use this installation method for Dolby Pro Logic applications (not Dolby Digital, DTS or other digital processing), where the receiver/processor is equipped with a subwoofer output, or a volumecontrolled preamp (line-) level output: Use RCA-type interconnects to connect the line-level subwoofer outputs on your receiver or amplifier to the line-level inputs on the subwoofer. IMPORTANT: Do not use the LFE input on the subwoofer with Dolby Pro Logic processors. Left Front ­ + Center ­ + Right Front ­ + Subwoofer Line Level In L R Receiver Left Front Subwoofer Out R L Right Front NOTE: If your receiver or amplifier has only one subwoofer output jack, then you will need to use a Y-connector (not included). Plug the male end of the Y-connector into your receiver or amplifier's subwoofer output jack, and connect each of the two female ends to separate RCA-type interconnects. Finally, plug the RCA-type interconnects into the line-level inputs on the subwoofer. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier. [. . . ] Turn everything back on, and determine whether the problem has followed the speaker or has remained in the same channel. If the problem is in the same channel, the source of the problem is most likely with your receiver or amplifier, and you should consult the owner's manual for that product for further information. If the problem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit www. jbl. com. If the system plays at low volumes but shuts off as volume is increased: · Check all wires and connections between receiver/ processor and speakers. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other. [. . . ]