User manual JBSYSTEMS LIGHT DMX 512 SUPER Z

[. . . ] How To Set The Unit 4. 1 Control Panel 4. 2 Main Function 5. How To Control The Unit 5. 1 By master/slave preprogrammed function 5. 2 By Akicolor Processor (AK-1) controller 5. 3 By universal DMX Controller 5. 4 DMX512 Configuration 5. 5 DMX512 Connection 6. Fixture Cleaning The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit's optics. [. . . ] - Synchronous color changing in Master/Slave linkage with adjustable changing speed. Dimension: 380mm x 240mm x 460mm / 15in x 9. 5in x 18. 2in(AK-250) 333mm x 200mm x 330mm / 13. 2in x 7. 9in x13 in(AK-150) Weight: 25 kg / 55 lbs(AK-250) / 9. 6 kg / 21. 3 lbs(AK-150) Beam angle: 4D 6. Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A. Check the connect power and circuit breaker. Measure the mains voltage on the main connector. Check DMX connectors, cables to see if link properly. Check the address settings and DMX polarity. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the unit or the previous one. Check in the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit. One of the channels is not working well 1. 3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) 5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) 5D AK-250 AK-150 3. 2 How To Install The Unit On The Floor 1. Disconnect from main power before making any type of connection. Refer to the unit's foot bracket hole pattern (B) to set the bolts (C) into the floor and screw the unit. Conjunction the unit's power supply cord to the mains power supply (D). Be sure that the local power outlet match that of the required voltage for your unit. If you have another unit, to link the unit together, please refer to chapter 5. 3 DMX512 Connection . Chase pattern: Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8 Pattern 9 Pattern 0 Changing colors at random, all units with same color Group changing colors ­ one by one Group changing colors ­ two by two Group changing colors ­ four by four Group changing colors ­ eight by eight Group changing colors ­ 16 by 16 Color chasing ­ one after one fixture in sequence Color chasing ­ 2 after 2 in sequence Color chasing ­ 4 after 4 in sequence Color chasing ­ 8 after 8 in sequence 5. 3 By universal DMX Controller If you use a universal DMX controller to control the units, you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal. Pressing ENTER Press the MENU button up to when the button and the display will light on. Use "-" and "+" button to change the DMX512 address. Once the address has been selected, press ENTER button to storing the setting. To go back to the functions without any change press the MENU button again. Please refer to the 6D following diagram to address your DMX512 channel for the units. - 5. 4 DMX512 Configuration 5. 1 By master/slave preprogrammed function By linking the units in master/slave connection, the first unit will control the other units to give an automatic sound activated synchronized light show. [. . . ] Use "-" and "+" button to change the DMX512 address. Once the address has been selected, press the ENTER button to setup the DMX address. To go back to the functions without any change press the MENU button again. Focus Adjust Press the MENU button up to when the is blinking on the display. Pressing ENTER button, the unit will focus on different color each time you press ENTER button. [. . . ]