User manual JBSYSTEMS LIGHT LED EXPO BEAM V 1.0

[. . . ] 3. 4--DMX512 SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8. 3. 5--RUN MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. 6--PERSONALITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. 7--ID ADDRESS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Always make sure that the equipment is installed securely. DO NOT stand close to the equipment and stare directly into the LED light source. Always disconnect the power supply before attempting and maintenance. Always make sure that the supporting structure is solid and can support the combined weight of the products. The earth wire must always be connected to the ground. Do not touch the power cables if your hands are wet. ATTENTION This product left the place of manufacture in perfect condition. In order to maintain this condition and for safe operation, the user must always follow the instructions and safety warnings described in this user manual. Avoid shaking or strong impacts to any part of the equipment. Make sure that all parts of the equipment are kept clean and free of dust. Always make sure that the power connections are connected correct and secure. If there is any malfunction of the equipment, contact your distributor immediately. When transferring the product, it is advisable to use the original packaging in which the product left the factory. Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent that their effectiveness is impaired. The lamp (LED) shall be changed if it has become damaged or thermally deformed. 1 PRODUCT(GENERAL) 15 3 2008. 9. 19 15 2 2. 1 INSTALLATION MOUNTING HANGING The LED PAR can be mounted in a hanging position using the supporting bracket. The bracket should be secured to the mounting truss or structure using a standard mounting clamp. Please note that when hanging the unit a safety cable should also be used. UPRIGHT The LED PAR can be mounted in an upright or sitting position using the supporting brackets. The LED MODULE can be mounted at any angle and in any position. It is possible to further adjust the angle of the LED MODULE using the two adjustment knobs located on the side of the fixture. 2. 2 POWER CONNECTIONS @ 220V: 50 units may be connected in series @120V: 25 units may be connected in series Note: As this fixture's DMX signal cable connection is Parallel connection, so if over 20 units to be connected, then a DMX signal amplifier is needed. 2 INSTALLATION 4 2008. 9. 19 2. 3 SETTING UP WITH A DMX512 CONTROLLER 2. 3-1 DMX512 ADDRESSING WITHOUT ID ADDRESSING (STUDIO 2 MODE) Connect the DMX512 controller to the units in series. Each unit has 6 DMX channels so the DMX Addresses should increase by increments of 6 (e. g. 1, 7, 13, 19. . . ) The ID address has not been set so therefore when using the controller CH8 must be inactive ( CH6=0 ). It is also possible to deactivate ID address selecting ID OFF from the Settings menu. on the fixture Each DMX Address may be used as many times as required. Any DMX address in the range from 001 to 512 may be used. Example: DMX Addr. 1 DMX Addr. 7 DMX Addr. 13 DMX512 CONTROLLER The figure above shows a simple DMX512 layout with the starting address of the first unit set at 1, with the second set at 7 and so on. . . [. . . ] Password is the same as the main access password. When uploading the MASTER and SLAVE units will be full on. . If an error occurs when uploading the MASTER and/or SLAVE units will display AMBER. On successful uploading of the custom programs the MASTER and SLAVE units will display WHITE. [. . . ]