User manual JBSYSTEMS WBS-2 V1.0

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual JBSYSTEMS WBS-2. We hope that this JBSYSTEMS WBS-2 user guide will be useful to you.

Lastmanuals help download the user guide JBSYSTEMS WBS-2.


Mode d'emploi JBSYSTEMS WBS-2
Download
Manual abstract: user guide JBSYSTEMS WBS-2V1.0

Detailed instructions for use are in the User's Guide.

[. . . ] `t Hofveld 2 ~ B1702 Groot-Bijgaarden ~ Belgium Reproduction or publication of the content in any manner, without express permission of the publisher, is prohibited. Dispose of the unit and used batteries in an environment friendly manner according to your country regulations. Thank you for buying this JB Systems product. To take full advantage of all possibilities, please read these operating instructions very carefully. [. . . ] On/off Switch: press this button several seconds to turn transmitter power on/off. Battery Compartment: Insert two AA rechargeable or dry (Alkaline) batteries into the compartment. Channel Selector: Use this rotary switch to choose one of the 16 available channels. It takes around 10 hours to recharge the batteries. while charging , the "low battery" indicator is flashing. Important note: be sure to insert rechargeable batteries (preferable "Ni-MH" type) in the transmitter before you connect the charger!Put these in vertical position during use. Power Indicator: The indicator LED lights when the receiver is ready to operate. B Indicators: These LEDs lights to show which antenna currently receives the RF Signal. If your audio mixer is equipped with a balanced input, it's better to connect the receiver using this XLR-output. Can be used to connect a guitar amplifier or any other unbalanced audio mixer input. Mic/Line Switch: used to select the output level of the XLR balanced connector or 6. Channel Selector: Use this rotary switch to choose one of the 16 available channels. : to prevent unwanted and disturbing noises, the squelch mutes the audio output of the receiver when the detected RF-signals of the are too weak. With the squelch control you can determine the minimum RF-signal level before audio output is not suppressed anymore. The squelch is already set in the factory so normally you don't need to change it. If you should adapt the squelch level for any reason, please set it to minimum before turning the receiver on and then slowly adjust using trial and error method. It takes around 10 hours to recharge the batteries. while charging , the "low battery" indicator on the transmitter is flashing. Important note: be sure to insert rechargeable batteries (preferable "Ni-MH" type) in the transmitter before you connect the charger!On/off Switch: press this button several seconds to turn transmitter power on/off. Low Battery LED: this LED indicates the battery life status. [. . . ] Press the power switch (2) for some seconds: one of the diversity LEDs (4) on the receiver should be lit to indicate that the RF-signal of the transmitter is captured. Speak through the mic: the AF indicator (3) will flash to the rhythm of your voice. If needed, you can still fine-tune the audio level with the gain knob (7). While checking the system, walk around to check if you encounter any dead spots (no reception): in these cases, try to change the position of the receiver. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE JBSYSTEMS WBS-2

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual JBSYSTEMS WBS-2 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag