User manual JENSEN JIMS-182 DATASHEET

[. . . ] Now it's time to consider how you can maximize the fun and excitement your equipment offers. This manufacturer and the Electronic Industries Association's Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing. Over time your hearing "comfort level" adapts to higher volumes of sound. [. . . ] To avoid this, you may need to move the unit further away from the TV or monitor if unnatural color shifts or image distortion occurs. 4 LOCATION OF CONTROLS Main Unit Top view Bottom view 21 1 22 2 12 7 9 6 11 5 10 4 38 Front view Rear view 16 15 13 14 15 20 19 18 17 1. iPod® Dock 2. iPod® Docking Connector 3. POWER On/Off Button To turn the unit on or off 4. VOLUME +/- Buttons Adjust the volume level up or down 5. SNOOZE/LIGHT Button Activate the snooze function; Turn the LCD backlight on or off 6. TUN +/- /iPod Buttons Tune the radio channel frequency up or down; iPod® Skip/Search Forward/Backward Buttons for Backward, for Forward. 7. CH +/- Buttons Select the preset radio stations 8. ALARM On/Off Button Switch the alarm on or off 9. SLEEP Button Select the time duration of the sleep timer 10. MODE Button Enter the setting mode 11. MEM/iPod Button Save the radio preset stations; save settings; iPod® PLAY/PAUSE 12. FUNCTION Button Select AM/FM Radio, iPod® mode and AUX (auxiliary input) mode 13. LCD Display 14. Remote Infra-red Sensor 15. Pair of Speakers 16. AUX in Jack An Audio Cable with a 3. 5mm stereo plug for the connection of external audio device 17. Cord Retracting Wheel For extending or retracting the auxiliary cord 18. DC Jack To connect to external DC power supply 19. Headphone Jack 20. FM Antenna Terminal 21. Battery Compartment It is to contain two 'AAA' batteries for clock back-up 22. RESET Button For resetting the unit 5 LOCATION OF CONTROLS Remote Control 1 6 7 RECORD 2 3 8 9 10 11 13 12 CH 4 5 12 1. Infra-red Transmitter 2. POWER On/Off Button 3. VOL +/- Button 4. FUNCTION Button 5. ALARM On/Off Button 6. SNOOZE/LIGHT Button 7. TUN Up/Down Buttons for Down, for Up 8. CH +/- Buttons 9. MEM Button 10. MODE Button 11. SLEEP Button 12. iPod® Skip/Search Forward/Backward Buttons for Backward, for Forward. 13. iPod® PLAY/PAUSE 14. Battery Compartment 14 6 RADIO OPERATIONS FM Antenna Connect the detachable FM Antenna Wire to the FM Antenna Terminal as instructed in the section "INSTALLATION". Fully extend the FM Antenna Wire for the maximum reception. Radio Tuning 1. Press the POWER button to turn on the unit. 2. Press the FUNCTION button repeatedly until "AM" or "FM" mode is reached. 3. In FM radio mode, if necessary, press the MODE button to select STEREO (ST) or MONO FM reception. 4. To manually tune the radio station, repeatedly press the TUN Up/Down Buttons. 5. To automatically search the next or previous station with the strongest signal, press and hold the TUN Up/Down Buttons until the frequency readout on the display begins to scan and then release the button. The tuner will stop scanning until the strongest signal station is searched. 2. Press the TUN +/- button to set the hour. 3. Press the VOL +/- button to set the minute. 4. Press the MEM button to confirm the settings. 12/24 Hour Time Display Mode Setting 1. Press the MODE button repeatedly until the 12/24 Hour Format Setting mode is reached. The flashing '12hr' or '24hr' will be displayed. 2. Press TUN +/- button to select 12 hour or 24 hour time display mode. 3. Press the MEM button to confirm the setting. Calendar Setting Year 1. Press the MODE button repeatedly until the year setting mode is reached. 2. To set the year, press the TUN +/- button to set the correct year. 3. Press the MEM button to confirm the setting. Month/Date 1. Press the MODE button repeatedly until the Month/Date setting mode is reached. [. . . ] Resetting the Unit If the unit is subject to a power surge or electric shock, it is possible that the internal micro-controller may lock up and the unit will not respond to any commands from the top panel controls or remote control. 1. In this event, unplug and then reconnect the AC power plug into the wall outlet. 2. Use a straightened paper clip, toothpick or similar objects to press the RESET button located on the bottom of the main unit (see the below figure). The reset operation clears the system memory and all of your previous settings will be erased. [. . . ]