User manual JENSEN SMPV-XGBLB DATASHEET

[. . . ] Failure to do so may result in the console breaking loose in the event of an accident. It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a television viewer or screen that is located in the motor vehicle at any point forward of the back of the driver's seat, or that is visible, directly or indirectly, to the driver while operating the vehicle. This product should only be installed to the rear of the driver's seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle. Required tools for installation: Electric drill ¼ steel drill bit " 1/8" steel drill bit Phillips screwdriver Socket wrench set with deep-well, 7/16" socket Box end wrench, size 7/16" Soldering Iron Two people are required for installation. 0892105 Bracket Kit 8007101 Bracket, Mounting 8007105 Screw, Hex #8x3/4 self drilling 8007106 Washer, 3/16" 8007110 Strap, Open, Nylon 8007111 Strap, Loop, Nylon 8007125 Bolt, ¼ ½ Hex "x1 ", 8007126 Washer, Fender 5/16" 8007128 Nut, Nylon Insert ¼ " 8007132 Installation Manual 1 4 20 20 1 1 4 4 4 1 P/N 8007132 Page 2 of 10 Rev. [. . . ] This product should only be installed to the rear of the driver's seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle. Required tools for installation: Electric drill ¼ steel drill bit " 1/8" steel drill bit Phillips screwdriver Socket wrench set with deep-well, 7/16" socket Box end wrench, size 7/16" Soldering Iron Two people are required for installation. 0892105 Bracket Kit 8007101 Bracket, Mounting 8007105 Screw, Hex #8x3/4 self drilling 8007106 Washer, 3/16" 8007110 Strap, Open, Nylon 8007111 Strap, Loop, Nylon 8007125 Bolt, ¼ ½ Hex "x1 ", 8007126 Washer, Fender 5/16" 8007128 Nut, Nylon Insert ¼ " 8007132 Installation Manual 1 4 20 20 1 1 4 4 4 1 P/N 8007132 Page 2 of 10 Rev. B There are six (6) steps to install the K-9 TV/VCP floor console: Step # 1 Step # 2 Step # 3 Step # 4 Step # 5 Step # 6 Remove face of the console Install brackets and the straps Install console to the floor of the vehicle Install VCP Install TV Replace console face STEP #1 REMOVE THE FACE OF THE CONSOLE Remove 4 Phillips screws securing face of console to body of console. 1) Disassemble shroud. P/N 8007132 Page 3 of 10 Rev. B Step #2 Install brackets and straps 1) Mount brackets using four screws. Do not use center hole. 2) Use soldering iron, if necessary, to melt holes in open strap, as shown. 3) Use soldering iron, if necessary, to melt holes in closed strap, as shown. P/N 8007132 Page 4 of 10 Rev. B 3) Pre-drill 1/8" pilot holes on bottom TV shelf for strap. P/N 8007132 Page 5 of 10 Rev. B 1) Attach both straps and customer-supplied harness, securing harness as needed. P/N 8007132 Page 6 of 10 Rev. Connect DC power connector (customer supplied) from console to DC power jack of VCP. Slide VCP into slot in front of console. P/N 8007132 Page 8 of 10 Rev. B STEP #5 INSTALL TV INTO CONSOLE Connect yellow RCA connector (customer supplied) to yellow RCA input jack on rear of television. Connect white RCA connector (customer supplied) to white RCA input jack on rear of television. Connect DC power connector (customer supplied) to rear of television. Connect coaxial cable antenna "F" connector (customer supplied)to rear of television "ANT" input. Secure television down with two straps. [. . . ] Connect DC power connector (customer supplied) to rear of television. Connect coaxial cable antenna "F" connector (customer supplied)to rear of television "ANT" input. Secure television down with two straps. [. . . ]