User manual JENSEN VOYAGER VCCS150

[. . . ] Give the interior a chance to cool down before starting playback. Use the Proper Power Supply This product is designed to operate with a 12 volt DC negative ground battery system. Protect the Disc Mechanism Avoid inserting any foreign objects into the disc slot. Misuse may cause malfunction or permanent damage due to the precise mechanism of this unit. [. . . ] Check that there will be sufficient space behind the dashboard for the radio chassis. Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. Follow the wiring diagram carefully and make certain all connections are secure and insulated with crimp connectors or electrical tape to ensure proper operation. secure part of the dashboard Screw Stud Hex Nut (5mm) either above or below the radio using the screw and plain Spring Washer washer provided. Bend the strap, as necessary, to position it. CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard from the weight of the radio or improper operation due to vibration. Re-attach the front panel to the chassis and test radio operation by referring to the operating instructions for the unit. Removing the Unit To remove the radio after installation: 1. Insert fingers into the groove in the front of frame and pull out to remove the frame. (When re-attaching the frame, point the side with a groove downwards and reattach. ) Insert the removal keys straight back until they click, and then pull the radio out. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc. · If the DCP is dirty, remove debris with a soft, dry cloth only. You can use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the DCP. PANEL RELEASE BUTTON 4 JCD2006 WIRING 688A 15 AMP FUSE ANTENNA SOCKET ANTENNA JACK 20-PIN AUDIO/POWER HARNESS (See Figure 1) REAR LINE OUT GREY WHITE L-CH RCA-TO-RCA CABLE (not supplied) RED R-CH AMP Figure 1: 20 PIN HARNESS PIN CHART 1 BLUE 2 12 3 13 4 14 5 15 6 16 7 17 8 18 9 19 10 20 Power Antenna Connect to power antenna or amplifier, If not used, tape bare end of wire. Ground Connect to ground terminal or clean unpainted metal part of chassis. 11 BLACK YELLOW Memory / Battery Connect to battery or 12 volt power source that is always live. The radio will not work if this wire is not connected. Accessory / Ignition Connect to existing radio wire or radio fuse. RED LEFT FRONT WHITE-BLACK LF- RIGHT FRONT GREY-BLACK RFGREY RF+ PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 WIRE COLOR GREY / BLACK GREY VIOLET VIOLET/BLACK EMPTY GREEN GREEN / BLACK RED BLACK RED WHITE WHITE / BLACK EMPTY BLUE YELLOW BLACK EMPTY EMPTY EMPTY WHITE FUNCTION / LABEL RIGHT FRONT SPEAKER ( ) RIGHT FRONT SPEAKER (+) RIGHT REAR SPEAKER (+) RIGHT REAR SPEAKER ( ) N/A LEFT REAR SPEAKER (+) LEFT REAR SPEAKER ( ) IGNITION (ACC) REAR PRE-AMPLIFIER LINE OUT COMMON RIGHT REAR PRE-AMPLIFIER LINE OUT LEFT FRONT SPEAKER (+) LEFT FRONT SPEAKER ( ) N/A POWER ANTENNA BATTERY (+) CHASSIS GROUND N/A N/A N/A LEFT REAR PRE-AMPLIFIER LINE OUT WHITE LF+ LEFT REAR GREEN-BLACK LR- RIGHT REAR VIOLET-BLACK RR- GREEN LR+ VIOLET RR+ 5 JCD2006 BASIC OPERATION Display (DISP) Press the DISP button (10) to view the clock. The LCD will display the clock for 5 seconds and then return to the previous display mode. Clock Adjustment With the clock displayed, press the DISP button (10) until the LCD flashes. Press the TUNE up >>| (7) button to adjust the minutes or the down TUNE |<< button to adjust the hour. CD PLAYER / RECEIVER Reset JCD2006 INT AS PS 40 WATTS X 4 RDM RPT CH CD -I N After releasing the control panel, use a pencil or any non-metallic object to press and hold the RESET button for five seconds to reset the main unit. The unit will return to the factory default settings. The reset button should be activated for the following reasons: · · · initial installation of the unit when all wiring is completed function buttons do not operate error symbol on the display RESET BUTTON 13 14 15 16 17 18 19 Control Panel Release ( ) NOTE: If after pressing the RESET button the unit still does not function normally, use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel. Press the release button (8) to release the control panel. [. . . ] Press MODE again to cancel Aux In mode and return to previous mode. 1 2 3 Left Audio Right Audio Ground 3. 5mm Audio In Cable (not included) 6 JCD2006 TUNER OPERATION Preset Scan Select a band (if needed). Press the TUNE |<< button to return to the beginning of the current track or press twice to skip to the previous track. The selected track number will appear on the display. Press and hold the TUNE >>| or |<< button (7) for more than 1 second to fast forward or fast reverse through the disc. [. . . ]