User manual JETWAY 603TCR4A

[. . . ] 603TCF/603TCFL USER'S MANUAL M/B For Socket 370 Pentium III Processor NO. G03-603TCR4A Release date: August 2002 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer. TABLE OF CONTENT USER'S NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii MANUAL REVISION INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 THERMAL SOLUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You may wish to connect the Power LED from the system case to this lead. Reset switch lead: RESET This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting in order to prolong the lift of the system's power supply. Speaker connector: SPEAKER This 4-pin connector connects to the case-mounted speaker. Power LED: PW LED The Power LED is light on while the system power is on. Connect the Power LED from the system case to this pin. 17 (9) Power switch: PWRIN This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system. Speaker R eset SW Turbo LE D VCC NC G ND G ND G ND NC VC C G ND VCC Keyboard Lock Power LE D Turbo SW/ SMI G ND G ND IDE LE -D PWR BTN System Case Connections (10) FAN Speed Headers (3-pin) : FAN1, FAN2 These connectors support cooling fans of 350mA (4. 2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan's plug to the board taking into consideration the polarity of connector. FAN1 1 3 3 1 FAN2 FAN Speed Headers (11) IR infrared module Headers (5-pin) : IR This connector supports the optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function. Pin 1 Infrared Module Headers 18 IR X R G ND IR TX VC C IR (12) CD Audio-In Headers (4-pin) : CD_IN CD_IN is the connector for CD-Audio Input signal. Please connect it to CDROM CD-Audio output connector. C -IN D 1 4 CD Audio-In Headers (13) Wake On-LAN Headers (3-pin) : WOL1 This connector connects to a LAN card with a WAKE ON-LAN output. This connector power up the system when a wake up signal is received through the LAN card. NOTE: This feature requires that BIOS Wake-Up by PCI Card is enabled. WOL1 3 1 Wake-On-LAN Headers (14) Line-In/Out, MIC Header (9-pin): AUDIO This header connect to Front Panel Line-In, Line-out, MIC connector with cable. Pin 1 Line-In/Out, MIC Headers 19 L-O UT-L L-IN-L G ND MIC L-IN-R G ND MICP G ND L-O UT-R AUDIO WO L G ND 5VSB 2-7 Starting Up Your Computer 1. After all connections are made, close your computer case cover. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V240V or 110V120V depending on your country's voltage used. Connect the power supply cord into the power supply located on the back of your system case according to your system user's manual. Turn on your peripheral as following order: a. Other external peripheral (Printer, Scanner, External Modem etc. . . ) c. For ATX power supplies, you need to turn on the power supply and press the ATX power switch on the front side of the case. The power LED on the front panel of the system case will light. The LED on the monitor may light up or switch between orange and green after the system is on. If it complies with green standards or if it is has a power standby feature. While the tests are running, the BIOS will alarm beeps or additional message will appear on the screen. [. . . ] Click NEXT to choose enabled DMA Mode 7. Click NEXT to Install VIA AGP VXD Driver 8. Click NEXT to Install VIA IRQ Routing Mini port Driver 9. Click Finish to restart computer 37 4-2 VGA Install VIA 8601 VGA Driver For WINDOWS 95/98/98SE/ME/NT4. 0/2000 1. [. . . ]