User manual JETWAY 865PBAR1A

[. . . ] 865PBA/865PBAP USER'S MANUAL M/B For LGA 775 Pentium 4 Processor NO. G03-865PBA Rev:1. 0 Release date: October 2004 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer. TABLE OF CONTENT USER'S NOTICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii MANUAL REVISION INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii COOLING SOLUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For performance issues, we strongly suggest you don't install a CD-ROM or DVD-ROM drive on the same IDE channel as a hard disk. Otherwise, the system performance on this channel may drop. 23 (12) Serial-ATA Port connector: SATA1/SATA2 This connector support the provided Serial ATA IDE hard disk cable to connecting the motherboard and serial ATA hard disk. Pin 1 SATA2 SATA1 On Chip Serial ATA Serial-ATA Port Connector 2-6-2 Headers (1) Line-Out, MIC Header (9-pin): AUDIO This header connect to Front Panel Line-out, MIC connector with cable. AUDIO AUD-MIC AUD- MIC-BIAS AUD-FPO -R UT HP-O N AUD-FPO -L UT Pin 1 2 AUD-G ND AUD-VCC AUD-RET-R AUD-RET-L 9 10 Line-Out, MIC Headers (2) USB Port Connector/Headers (9-pin) : USB2, USB3 The USB2, USB3 is for internal connecting USB device directly. The USB2 header is used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel. +D ATA G ND O C -DATA Pin 1 Pin 1 +DATA G ND USB Port Headers 24 +D ATA G ND -DATA -DATA VC C VC C +DATA G ND O C -DATA VC C VC C USB3 USB2 (3) (4) (5) Speaker connector: SPEAK This 4-pin connector connects to the case-mounted speaker. IDE Activity LED: IDE LED This connector connects to the hard disk activity indicator light on the case. Reset switch lead: RESET This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting in order to prolong the lift of the system's power supply. See the figure below. (6) Power LED: PWR-LED The Power LED is light on while the system power is on. Connect the Power LED from the system case to this pin. (7) Power switch: PWR BTN This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system. PRD W LE PR W BTN R SE ET SPEAK P1 in JW_FP P1 in SP KR NC G ND VC C5 System Case Connections (8) FAN Headers (4-pin) : CPUFAN FAN Headers (3-pin) : SFAN1, SFAN2 These connectors support cooling fans of 350mA (4. 2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan's plug to the board taking into consideration the polarity of connector. 4 1 C PUFAN 1 3 SFAN1 1 3 SFAN2 FAN Headers 25 H LE DD VC 5 C H DLE DD G ND R STSW NC VC C5 PW LE RD PR W BTN G ND (9) IR infrared module Headers (5-pin) : IR This connector supports the optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function. 2 GD N IR X R 6 5 IR Pin 1 IR infrared module Headers (10) CD Audio-In Headers (4-pin) : CDIN CDIN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-Audio output connector. 4 C DIN CD Audio-In Headers (11) Game Port Header: GAME GAME Pin 1 GAME Port Headers 26 NC VC C5 IR TX 1 2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V240V or 110V120V depending on your country's voltage used. Connect the power supply cord into the power supply located on the back of your system case according to your system user's manual. Turn on your peripheral as following order: a. Other external peripheral (Printer, Scanner, External Modem etc. . . ) c. For ATX power supplies, you need to turn on the power supply and press the ATX power switch on the front side of the case. The power LED on the front panel of the system case will light. The LED on the monitor may light up or switch between orange and green after the system is on. [. . . ] Then AVRACK Windows appears 5. Sound Effect select and KaraOK Mode Function 6. Manual Sound Effect Setting Note: The path of the file For WIN98/NT4. 0/WIN2K/XP is X:\CODEC\ALC\SETUP. EXE Note: In Win2K/WinME users have to click Control Panel\System\Device Manager\ DVD\CD-ROM drives to Enabled digital CD Audio for the CD-ROM Device when use the SPDIF-Out digital signal. 46 4-3 LAN install VIA 6105 LAN Controller Driver WINDOWS 98SE/98ME/2000/XP Setup 1. Click LAN when Magic Install Menu appear 2. Install VIA VT6105 PCI 10/100M Fast Ethernet Driver 3. Select YES and Restart your computer X:\VIALAN\WIN98 (If OS is win9X) 47 4-4 USB2. 0 install Intel USB2. 0 Driver Windows 98SE/ME USB 2. 0 Driver installation 1. Click USB2. 0 when Magic Install Menu appear 2. [. . . ]