User manual JETWAY 915GCPR2A

[. . . ] 915GCP/915GC 915PCP/915PC USER'S MANUAL M/B For LGA 775 Pentium 4 Processor NO. G03-915GCP Rev:2. 0 Release date: November 2004 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer. TABLE OF CONTENT USER'S NOTICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii MANUAL REVISION INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii COOLING SOLUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly. Please refer to the documentation of your hard disk for the jumper settings. IDE 1 Pin 1 · · Two hard disks can be connected to each connector. The first HDD is referred to as the "Master" and the second HDD is referred to as the "Slave". For performance issues, we strongly suggest you don't install a CD-ROM or DVD-ROM drive on the same IDE channel as a hard disk. Otherwise, the system performance on this channel may drop. 23 (13) Serial-ATA Port connector: SATA1/SATA2/SATA3/SATA4 This connector support the provided Serial ATA IDE hard disk cable to connecting the motherboard and serial ATA hard disk. Pin 1 SATA4 SATA3 SATA2 SATA1 Serial-ATA Port Connector 2-6-2 Headers (1) Line-Out, MIC Header (9-pin): AUDIO This header connect to Front Panel Line-out, MIC connector with cable. AUD-G ND AUD-VC C AUDIO Pin 1 2 10 9 Line-Out, MIC Headers (2) USB Port Headers (9-pin) : USB3, USB4 The header is used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel. +DATA G ND O C AUD-MIC AUD-MIC-BIAS AUD-FPO -R UT HP- O N AUD- FPO -L UT -DATA Pin 1 Pin 1 +DATA G ND -DATA USB Port Headers (3) (4) Speaker connector: SPEAK This 4-pin connector connects to the case-mounted speaker. Power LED: PWR-LED The Power LED is light on while the system power is on. Connect the Power LED from the system case to this pin. 24 +D ATA G ND -DATA VC C VC C -DATA VC C VC C USB3 +DATA G ND O C USB4 (5) (6) (7) IDE Activity LED: IDE LED This connector connects to the hard disk activity indicator light on the case. Reset switch lead: RESET This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting in order to prolong the lift of the system's power supply. Power switch: PWR BTN This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system. PWR LED PWRBTN PWRBTN PWRLED VCC5 PWRLED Pin 1 Pin 1 SPEAK JW FP Pin 1 SPKR NC VCC5 GND HDLED System Case Connections (8) Wake On-LAN Headers (3-pin) : WOL This connector connects to a LAN card with a WAKE ON-LAN output. This connector power up the system when a wake up signal is received through the LAN card. NOTE: This feature requires that Wake On LAN or Ring In Wake up is enabled. WOL 1 3 Wake-On-LAN Headers (9) FAN Power Headers: SYSFAN1, SYSFAN2 (3-pin), CPUFAN (4-pin) These connectors support cooling fans of 350mA (4. 2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan's plug to the board taking into consideration the polarity of connector. 25 5VSB G ND WO L RESET GND RSTSW NC VCC5 HDDLE GND CPUFAN SYSFAN1 1 1 4 3 SYSFAN2 3 1 FAN Power Headers (10) IR infrared module Headers (5-pin) : IR This connector supports the optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function. 2 Pin 1 G ND IR RX IR 6 5 IR infrared module Headers (11) CD Audio-In Headers (4-pin) : CDIN CDIN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-Audio output connector. 4 C DIN CD Audio-In Headers (12) SPDIF In/Out Header: JP6 SPDIF UT -O G ND NC G ND JP6 2 Pin 1 SPDIF-Bracket Connector 26 NC SPF -IN1 IF SPD -IN2 IF NC 12V NC VCC 5 IRTX 1 10 9 +12V C PUFAN O UT G ND C PUFAN IN 2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V240V or 110V120V depending on your country's voltage used. Connect the power supply cord into the power supply located on the back of your system case according to your system user's manual. Turn on your peripheral as following order: a. Other external peripheral (Printer, Scanner, External Modem etc. . . ) c. For ATX power supplies, you need to turn on the power supply and press the ATX power switch on the front side of the case. [. . . ] Click NEXT when Chipset Software Install Utility appears 3. This license agreement appear, click Yes, the 4. Select if you want computer re-started click readme information appear, click Next Finish 4-2 VGA install Intel 915G VGA Driver (For 915GCP/915GC) 1. Click NEXT When Intel (R) Graphics Media appears Accelerator Driver Software Setup appear 45 3. [. . . ]