User manual JETWAY 917GBAR3A

[. . . ] 917PBAG/917PBA 917GBAG/917GBA USER'S MANUAL M/B For LGA 775 Pentium 4 Processor NO. G03-917GBA Rev:3. 0 Release date: March 2005 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer. TABLE OF CONTENT USER'S NOTICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii MANUAL REVISION INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii COOLING SOLUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The first HDD is referred to as the "Master" and the second HDD is referred to as the "Slave". For performance issues, we strongly suggest you don't install a CD-ROM or DVD-ROM drive on the same IDE channel as a hard disk. Otherwise, the system performance on this channel may drop. (14) Serial-ATA Port connector: SATA1/SATA2/SATA3/SATA4 This connector support the provided Serial ATA IDE hard disk cable to connecting the motherboard and serial ATA hard disk. Serial-ATA RAID Port connector: SATA5/SATA6 This port support RAID0, RAID1, RAID0+1 functions. Pin 1 SATA4 SATA3 SATA2 SATA1 Pin 1 SATA6 SATA5 Serial-ATA RAID Port Serial-ATA Port Connector 2-6-2 Headers (1) Line-Out, MIC Header (9-pin): AUDIO This header connect to Front Panel Line-out, MIC connector with cable. AUD-G ND AUD-VC C AUDIO Pin 1 2 10 9 Line-Out, MIC Headers (2) USB Port Headers (9-pin) : USB3, USB4 The header is used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel. 24 AUD-MIC AUD-MIC-BIAS AUD-FPO -R UT HP- O N AUD- FPO -L UT +DATA G ND O C -DATA Pin 1 Pin 1 +DATA G ND -DATA USB Port Headers (3) (4) IDE Activity LED: IDE LED This connector connects to the hard disk activity indicator light on the case. Reset switch lead: RESET This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting in order to prolong the lift of the system's power supply. Power LED: PWR-LED The Power LED is light on while the system power is on. Connect the Power LED from the system case to this pin. Speaker connector: SPEAK This 4-pin connector connects to the case-mounted speaker. Power switch: PWR BTN This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system. PWR LED PWRBTN PWRBTN PWRLED (5) (6) (7) VCC5 PWRLED Pin 1 JW FP SPEAK Pin 1 SPKR NC VCC5 Pin 1 GND HDLED System Case Connections (8) FAN Power Headers: SYSFAN1, SYSFAN2 (3-pin), CPUFAN (4-pin) These connectors support cooling fans of 350mA (4. 2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan's plug to the board taking into consideration the polarity of connector. 25 RESET GND RSTSW NC VCC5 HDDLE GND +D ATA G ND -DATA VC C VC C -DATA VC C VC C USB3 +DATA G ND O C USB4 CPUFAN SYSFAN1 1 1 4 3 SYSFAN2 3 1 FAN Power Headers (9) IR infrared module Headers (5-pin) : IR This connector supports the optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function. 2 Pin 1 G ND IR RX IR 6 5 IR infrared module Headers (10) CD Audio-In Headers (4-pin) : CDIN CDIN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-Audio output connector. 4 C DIN CD Audio-In Headers (11) SPDIF In/Out Header: JP6 SPDIF UT -O G ND NC G ND JP6 2 Pin 1 SPDIF-Bracket Connector 26 NC SPF -IN1 IF SPD -IN2 IF NC 12V NC VCC 5 IRTX 1 10 9 +12V C PUFAN O UT G ND C PUFAN IN 2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V240V or 110V120V depending on your country's voltage used. Connect the power supply cord into the power supply located on the back of your system case according to your system user's manual. Turn on your peripheral as following order: a. Other external peripheral (Printer, Scanner, External Modem etc. . . ) c. For ATX power supplies, you need to turn on the power supply and press the ATX power switch on the front side of the case. The power LED on the front panel of the system case will light. The LED on the monitor may light up or switch between orange and green after the system is on. [. . . ] Click NEXT When Intel (R) Graphics Media appears Accelerator Driver Software Setup appear 3. Click YES, This is Announce CopyRight 4. If You Want Re-start Computer , Click FINISH 4-3 SOUND install ALC880 AC97 Codec Audio Driver 1. Click SOUND when MAGIC INSTALL MENU appears 2. [. . . ]