User manual JETWAY 917PDCPR106

[. . . ] 917PDCP/917PDCG 917GDCP/917GDCG USER'S MANUAL M/B For LGA 775 Pentium 4 Processor NO. G03917PDCPR106 Rev:1. 0 Release date: June 2005 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer. TABLE OF CONTENT USER'S NOTICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii MANUAL REVISION INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii COOLING SOLUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Power switch: PWR BTN This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system. PWR LED PWRBTN PWRBTN PWRLED (5) (6) (7) VCC5 PWRLED Pin 1 JW FP SPEAK Pin 1 SPKR NC VCC5 Pin 1 GND HDLED System Case Connections (8) FAN Power Headers: SYSFAN1, SYSFAN2 (3-pin), CPUFAN (4-pin) These connectors support cooling fans of 350mA (4. 2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan's plug to the board taking into consideration the polarity of connector. C PUFAN O UT 4 RESET 1 CPUFAN SYSFAN1 1 3 SYSFAN2 3 1 FAN Power Headers (9) IR infrared module Headers (5-pin) : IR 25 +12V G ND C PUFAN IN GND RSTSW NC VCC5 HDDLE GND This connector supports the optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function. 2 Pin 1 G ND IR RX 6 5 NC VCC 5 IRTX 1 10 9 IR IR infrared module Headers (10) CD Audio-In Headers (4-pin) : CDIN CDIN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-Audio output connector. 4 C DIN CD Audio-In Headers (11) SPDIF In/Out Header: JP6 (SPDIF Bracket Optional) JP6 2 Pin 1 SPDIF-Bracket Connector 26 NC SPF -IN1 IF SPD -IN2 IF NC 12V SPDIF UT -O G ND NC G ND 2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V240V or 110V120V depending on your country's voltage used. Connect the power supply cord into the power supply located on the back of your system case according to your system user's manual. Turn on your peripheral as following order: a. Other external peripheral (Printer, Scanner, External Modem etc. . . ) c. For ATX power supplies, you need to turn on the power supply and press the ATX power switch on the front side of the case. The power LED on the front panel of the system case will light. The LED on the monitor may light up or switch between orange and green after the system is on. If it complies with green standards or if it is has a power standby feature. While the test are running, the BIOS will alarm beeps or additional message will appear on the screen. If you do not see any thing within 30 seconds from the time you turn on the power. The system may have failed on power-on test. Recheck your jumper settings and connections or call your retailer for assistance. Beep Meaning One short beep when displaying logo Long beeps in an endless loop One long beep followed by three short beeps High frequency beeps when system is working No error during POST No DRAM install or detected Video card not found or video card memory bad CPU overheated System running at a lower frequency 6. During power-on, press <Delete> key to enter BIOS setup. Power off your computer: You must first exit or shut down your operating system before switch off the power switch. For ATX power supply, you can press ATX power switching after exiting or shutting down your operating system. [. . . ] You may copy from DRIVER CD X:\FLASH\AWDFLASH. EXE or download from our web site. Copy latest BIOS for 917PDCP from our web site to your boot disc. Insert your boot disc into A:, start the computer, type "Awdflash A:\917PDCAxxx. BIN /SN/PY/CC/R" 917PDCxxx. BIN is the file name of latest BIOS it can be 917PDCA03. BIN or 917PDC02. BIN SN means don't save existing BIOS data PY means renew existing BIOS data CC means clear existing CMOS data R means restart computer STEP 5. Push ENTER and the BIOS will be updated, computer will be restarted automatically. 51 4-8 Pro Magic Plus Function Introduction What's Pro Magic Plus? Tired with reinstall OS each time when it doesn't work? [. . . ]