User manual JETWAY S755TWIN

[. . . ] S755TWIN USER'S MANUAL M/B For Socket 754 AMD Athlon64 Processor NO. G03-S755T8 Rev:1. 0 Release date: April 2003 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer. TABLE OF CONTENT USER'S NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii MANUAL REVISION INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii COOLING SOLUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] We also find Diamond Vipper V770 golden finger is design for 2X/4X mode AGP Slot. It can be adjusted the jumper for AGP 2X (3. 3V) or AGP 4X (1. 5V). But the factory default setting is 2X (3. 3V). If you install this AGP card in motherboard without change the jumper setting to 4X (1. 5V), it will burn the motherboard. 2-6 Connectors, Headers 2-6-1 Connectors (1) Power Connector (20-pin block) : PWR2 ATX Power Supply connector. This is a new defined 20-pins connector that usually comes with ATX case. The ATX Power Supply allows to use soft power on momentary switch that connect from the front panel switch to 2-pins Power On jumper pole on the motherboard. When the power switch on the back of the ATX power supply turned on, the full power will not come into the system board until the front panel switch is momentarily pressed. Press this switch again will turn off the power to the system board. PIN ROW2 ROW1 Pin 1 1 2 3 4 5 6 7 8 9 10 3. 3V -12V GND Soft Power On GND GND GND -5V +5V +5V 3. 3V 3. 3V GND 5V GND 5V GND Power OK +5V (for Soft Logic) +12V (2) ATX 12V Power Connector (4-pin block) : PWR1 This is a new defined 4-pins connector that usually comes with ATX Power Supply. The ATX Power Supply which fully support Pentium 4 processor must including this connector for support extra 12V voltage to maintain system power consumption. Without this connector might cause system unstable because the power supply can not provide sufficient current for system. 12 Pin 1 (3) (4) (5) (6) (7) (8) USB Port connector: USB1, USB2 The connectors are 4-pin connector that connect USB devices to the system board. LAN Port connector: LAN This connector is standard RJ45 connector for Network connector. PS/2 Mouse & PS/2 Keyboard Connector: KBMS (PS2 KB/MOUSE) The connectors for PS/2 keyboard and PS/2 Mouse. Parallel Port Connector (25-pin female): PRINT Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. The On-board Parallel Port can be disabled through the BIOS SETUP. Please refer to Chapter 3 "INTEGRATED PERIPHERALS SETUP" section for more detail information. Audio Line-In, Lin-Out, MIC Connector : CN1 This Connector are 3 phone Jack for LINE-OUT, LINE-IN, MIC Audio output to speaker Line-out : Audio input to sound chip Line-in : Microphone Connector MIC : Serial Port COM1: COM1/COM2 COM1/COM2 is the 9-pin D-Subminiature mail connector. The On-board serial port can be disabled through BIOS SETUP. Please refer to Chapter 3 "INTEGRATED PERIPHERALS SETUP" section for more detail information. PS/2 Mouse PRINT USB1 LAN MIC LINE-IN LINE-OUT PS/2 Keyboard COM1 COM2 UL_B (9) Floppy drive Connector (34-pin block): FDC This connector supports the provided floppy drive ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to the floppy drives. FDC Pin 1 Floppy Drive Connector 13 (10) Primary IDE Connector (40-pin block): IDE1 This connector supports the provided IDE hard disk ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly. Please refer to the documentation of your hard disk for the jumper settings. [. . . ] PC-CILLIN install PC-CILLIN2002 anti-virus program installs SMART GUARDIAN software for hardware monitoring device 9. BROWSE CD to browse the contents of the CD 11. EXIT to exit from MAGIC INSTALL menu 4-1 AGPVXD Install SiS AGPVXD Driver 36 The AGPVXD Driver is Only For AGP Slot VGA CARD User, before install AGP card driver please install this AGPVXD driver first. The path of the file: for WINDOWS 9X is X:\SIS755\AGPVXD\WIN9X\SETUP. EXE (including WIN95/98/98SE/ME) for WINDOWS 2000/XP is X:\SIS755\AGPVXD\WIN2K_XP\SETUP. EXE For WINDOWS 95/98/98SE/ME/2000/XP 1. Click AGPVXD when Magic Install MENU appears 2. Click Next when SiS Acceleration Graphic Port appears 3. Click NEXT or choose BROWSE to change the path For the file to be stored 4. After Setup complete please select restart my computer now and click Finish to complete setup 4-2 IDE Install SiS MINI IDE Driver 37 1. Click IDE when Magic Install main menu appear 2. Click NEXT when SIS IDE Driver Setup window appear 3. Select components and Click Next 4. Click FINISH and Restart Computer 4-3 SOUND Install ALC Audio Codec Driver 1. [. . . ]