User manual JETWAY V500DAR1A

[. . . ] V500DA / V500DAP User's Manual AMD Socket 462 Processor Motherboard VIA KT400 + VIA 8237 Revision 1. 0 P / N: G03 -V500DA Table of Content Manual Revision History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Copyright Announcement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Trademarks Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] After all connection are ready, close your computer case cover. Be sure all the switches are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V240V or 110V120V depending on your country's voltage used. Connect the power supply cord into the power supply located on the back of your system case according to your system user's manual. Turn on your peripherals as following order: a. Other external peripherals (Printer, Scanner, External Modem etc. . . ) c. For ATX power supplies, you need to turn on the power supply and press the ATX power switch on the front side of the case. The power LED on the front panel of the system case will light. The LED on the monitor may light up or switch between orange and green after the system is on. If it complies with green standards or if it is has a power standby feature. While the test are running, the BIOS will alarm beeps or additional message will appear on the screen. If you do not see any thing within 30 seconds from the time you turn on the power. The system may have failed on power-on test. Recheck your jumper settings and connections or call your retailer for assistance. Beep One short beep when displaying logo Long beeps in an endless loop One long beep followed by three short beeps High frequency beeps when system is working Meaning No error during POST No DRAM install or detected Video card not found or video card memory bad CPU overheated System running at a lower frequency Follow the instructions in 6. During power-on, press <Delete> key to enter BIOS setup. Power off your computer: You must first exit or shut down your operating system before switch off the power switch. For ATX power supply, you can press ATX power switching after exiting or shutting down your operating system. If you use Windows 9X, click "Start" button, click "Shut down" and then click "Shut down the computer?" The power supply should turn off after windows shut down. 19 Chapter 3 Introducing BIOS Settings The BIOS is a program located on a Flash Memory of the motherboard. Using this program as a bridge between motherboard and operating system. When the computer starting to work, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. Only when these tasks are completed done it gives up control of the computer to operating system (OS). [. . . ] VIA 4 IN 1 install VIA Service Pack 4 IN 1 driver 2. SOUND install AC97 Audio Codec Installing driver 3. LAN USB2. 0 SATA DIRECTX8 PC-CILLIN PC-HEALTH MAGIC BIOS BROWSE CD EXIT install VIA LAN Controller driver (for V500DAP) install USB 2. 0 driver install VIA Serial ATA driver install Microsoft DirectX 8. 1 driver install PC-CILLIN2004 anti-virus program install Winbond PC-HEALTH hardware monitor Software install BIOS Live Update Utility to browse the contents of the CD to exit from MAGIC INSTALL menu 41 4-1 VIA 4IN1 * IDE : AGPVXD : Install VIA Service Pack 4 IN 1 Driver The path of the file is X:\VIA\DRIVER\SETUP. EXE VIA ATAPI VENDOR SUPPORT DRIVER IS USED TO FIXED COMPATIBILITY ISSUE FOR IDE DEVICES VIA AGPVXD DRIVER IS TO BE INSTALLED, IF YOU ARE USING AN AGP VGA CARD, VIAGART. VXD WILL PROVIDE SERVICE ROUTINES TO YOUR VGA DRIVER AND INTERFACE DIRECTLY TO HARDWARE, PROVIDING FAST GRAPHIC ACCESS IRQ ROUTING : VIA PCI IRQ MINIPORT DRIVER IS TO BE INSTALLED UNDER WIN98 ONLY, IT WILL FIX PCI IRQ ROUTING SEQUENCE INF : VIA REGISTRY DRIVER IS TO BE INSTALLED UNDER WINDOWS THE DRIVER WILL ENABLE VIA POWER MANAGERMENT CONTROLLER 1. Click IDE when MAGIC INSTALL MENU 2. appears Click NEXT when VIA Service Pack Wizard appears 3. This is to announce the Copy Write, click Yes 4. Click NEXT to choose all driver 42 5. Click NEXT to Install ATAPI Vender Support Driver 6. Click NEXT to choose enabled DMA Mode 7. Click NEXT to Install VIA AGP VXD Driver 8. Click NEXT to Install VIA IRQ Routing Mini port Driver 9. Click Finish to restart computer 43 4-2 SOUND install ALC AC97' Codec Audio Driver 1. [. . . ]