User manual JOHN LEWIS JLBICH602

[. . . ] The appliance must not be used as a work surface or as a storage surface. · Only clean this hob in accordance with the instructions. Additions or modifications to the appliance are not per· For cleaning, the appliance must be switched off and mitted. Repairs to the appliance must only be carried out cooled down. [. . . ] structions supplied by qualified and competent personnel to the relevant National Standards. · Clean the worktop in the area of the cut-out section. · Stick the one-sided self-adhesive sealing tape supplied all the way round the lower edge of the cooking surface along the outer edge of the glass ceramic panel. The cut ends should lie in the middle of one side. When you have cut it to length (add a few mm), press the two ends flush up against one another. · A protective floor must be installed under the appliance. 6 7 8 The Control Panel Cooking zones and heat setting selection Display On/Off Touch Control sensor fields The appliance is operated using the Touch Control sensor fields. Functions are controlled by touching sensor fields and confirmed by displays. Touch the sensor fields from above, without covering other sensor fields. Sensor field On / Off Increase settings Reduce settings Select cooking zone Increases heat setting Reduces heat setting Function Switches appliance on and off Displays Display Description Cooking zone is switched off Heat settings Fault Residual heat Child safety device Heat setting is set Malfunction has occurred Cooking zone is still hot Lock/child safety device is set. ¾ ¿-Ç ER h l 9 Residual heat indicator 1 Warning!After 3 Residual heat can be used for melting and keeping food warm. Control panel Switch on Switch off Touch Touch for 2 seconds for 1 second being switched off, the cooking zones need some time to cool down. Look at the residual heat indicator h . Switching the appliance on and off Display ¾ / Decimal point flashes h / none Selecting the cooking zone Control panel Select Touch Display ¾ Decimal point illuminates 3 The decimal point is displayed by the selected cookSelecting the heat setting ing zone. Then a heat setting must be set for this cooking zone within 6 seconds, otherwise it must be re-selected. 3 After selecting the cooking zone, briefly release the sensor field . Control panel Increase Decrease Switch off Touch Touch Touch and at the same time Display ¾ to Ç Ç to ¾ ¾ 3 After 6and the decimal no input theout. To set thecanseconds with selection is celled point goes required cooking zone again, make another selection. 10 Using the child safety device The child safety device prevents unintentional use of the appliance. Setting the child safety device Step 1. Control panel Switch on appliance (Do not set a heat setting) Touch of the front right cooking zone and the same time Touch of the front right cooking zone Display ¾ / h (if hot) at 4 x ¾ or h Decimal points flash l Appliance switches off. 3 To override the child safety device or switch it off successfully, the steps must be performed immediately one after the other. No other sensor fields must be touched between the steps described. If the steps are performed in the wrong order, the display automatically switches itself off. Overriding the child safety lock The child safety device can be released in this way for a single cooking session; it remains activated afterwards. Control panel Switch on the appliance Touch of the front right cooking zone and the same time Display l / h (if hot) at 4 x ¾ Decimal points flash Until the appliance is next switched off, it can be used as normal. Cancelling the child safety device Step 1. Control panel Switch on the appliance Touch of the front right cooking zone and the same time Touch Display l / h (if hot) at 4 x ¾ or h Decimal points flash Appliance switches off. 11 Safety cut-out Cooking surface · If after switching on the appliance a heat setting is not set for a cooking zone within approx. 10 seconds, the appliance automatically switches itself off. · If one or more sensor fields are touched for longer than approx. 10 seconds, the cooking surface is automatically switched off. [. . . ] In the event of a fault occurring which you cannot resolve yourself from advice given within this instruction manual your first step is to contact our extended warranty administrators on 0870 0107887 who will give you details for your local Service Force. When contacting Service Force, please quote the model (Mod. ) and serial number (S. N. ), both of which are shown on the rating plate located underneath the hob. So that you always have these numbers at hand, we recommend you to make a note of them here: Mod. : PNC: S. N. : Your hob is covered by a 3 year parts and labour guarantee (see separate details given at point of sale). Please retain your purchase receipt safely for the service engineer to verify the purchase details. . Spare parts This product should be serviced by any authorised service engineer; and only genuine spare parts should be used. [. . . ]