User manual JOHN LEWIS JLBIHD904

[. . . ] · When installed between adjoining wall cabinets the wall cabinets must not overhang the hob. · If the room where the hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the room sealed or balanced flue type. · If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the room. · The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose. [. . . ] Vr 11 12a 650 min. 116 116 306 Fitting the Canopy Hood · Before starting to fix the hood body, tighten the two screws item Vr located on the top of the hood body. · Hook the hood body onto the two screws item 12a. · Fully tighten the screws item 12a. · Using a screw driver and spirit level, adjust the screws item Vr until the hood body is level. 12a X 7. 2. 1 1÷2 6 Extraction (Ducted) The cooker hood is more effective when installed in the extraction mode (ducted to the outside). Venting kits may be purchased through your retailer or DIY store, and must be evacuated through an outside vent of ø125 (5ins) or ø150mm (6ins). The ducting used must be manufactured from fire retardent material conforming to the relevant British Standard or DIN 4102-B1. When the cooker hood is ducted to the outside the charcoal filter must be removed. Fitting the Ducting · Fit the ø150mm (6ins) ducting to the spigot on top of the hood body as illustrated. · When using ø125mm (5ins) ducting fit item 9 and 10 on to the spigot on the top of the hood body as illustrated. · For the best performance use the shortest possible run of ducting and we recommend the use of rigid pipe in preference to flexible hose as this will improve the flow of air while reducing turbulence, which causes noise and a loss of performance. · If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler, then its flue must be be of the room sealed or balanced flue type. · If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the room. · The cooker ducting when fitted in the extraction mode must never be connected to central heating flues, radiators or water heaters. ø 150 9 ø 125 10 Recirculation Mode The cooker hood is supplied specified for use in the recirculation mode, with the charcoal filter fitted. In the recirculation mode contaminated air is passed through the charcoal filter to be purified and recirculated into the kitchen through the grille outlets on either side of the chimney. · Assemble the two halves of the ducting extension pipe item 14. · Push-fit the extension pipe on to the ducting spigot on top of the canopy. · Push-fit the recirculation adapter item 15 on to extension pipe item 14. · Insert the recirculation outlet extensions item 14. 4 into the recirculation adapter item 15. · The recircualtion grilles item 8a and 8b must be fitted after the lower chimney item 2. 2 has been fitted. · Ensure the activated charcoal filter has been fitted. 8b 14 15 14. 1 8a 7 Fitting the Upper Chimney · Expand the sides of the upper chimney stack item 2. 1 and place the chimney over the two brackets 7. 2. 1 ensuring they are well seated. · Secure the chimney stack to the brackets 7. 2. 1 using the four self tapping screws item 12c (2. 9 x 9. 5mm) supplied. [. . . ] · If set up for recirculation, check that the charcoal filter is still effective. · If set up for extraction, check that the ducting and outlets are not blocked. · The safety cut-out device has been tripped. · Tum off the hob and then wait for the device to reset. The cooker hood has switched off during operation Repairs and After Sales Service In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact our extended warranty administrators by telephoning: When you contact the Service Force Centre you will need to give the following details: 1. [. . . ]