User manual JONSERED 380

[. . . ] les r un ratio reco we tierio ly a mo on RNerate and de e Us WA t op wear ged. no Do ct to dama or subjeed ck cra ING r is taine en . Con wh r. Re conta erlyi ently nt prop qu ceme r is g fre pla ine ba d re nta eck de s co Ch mmen n. les r unrioratio reco a INGmowe tie only RNerate and de e Us WA t op wear ged. [. . . ] Each step of the assembly instructions will identify the group needed for that step. BAG OF PARTS CONTENTS ASSEMBLY LOCATION HARDWARE SHOWN ACTUAL SIZE GROUP "A" REAR MOUNTING BRACKET AND SUPPORT TUBE TO DRAW BAR (4) Shoulder Bolt 5/16 - 18 Self Tapping (4) Bolt 5/16 - 18 x 3/4 (4) Locknut 5/16-18 (2) Wing Nut (1) Support Plate NOT SHOWN FULL SIZE (2) Washer 11/32 x 1-1/2 x 10 Ga. (2) Lock Washer 5/16 GROUP "B" SUPPORT POST TO COVER ASSEMBLY (3) Carriage Bolt 5/16 - 18 x 3/4 (3) Locknut 5/16-18 4 BAG OF PARTS CONTENTS (continued) SUPPORT TUBE TO COVER ASSEMBLY GROUP "C" (1) Bolt 5/16 - 18 x 3/4 (1) Bolt 5/16 - 18 x 2-1/4 (1) Bracket Support Pin (2) Locknut 5/16-18 GROUP "D" SUPPORT POST TO MOUNTING BRACKET (1) Retainer Spring (4) Tubing End Caps GROUP "E" (2) Latch Hook Assembly LOWER CHUTE ASSEMBLY TO MOWER DECK (2) Screw #10 x 5/8 (2) Washer, Lock #10 (2) Washer 3/16 x 3/4 x 16 Ga. CHUTE LATCH ASSEMBLY to UPPER CHUTE (2) Nut, Weld #10 GROUP "F" (1) Screw #10 x 1-1/8 (2) Washer 3/16 x 3/4 x 16 Ga. (1) Spacer, Split #10 (1) Nut, Acorn #10 GROUP "G " (1) Rubber Latch CHUTE LATCH ASSEMBLY to LOWER CHUTE (1) Screw #10 x 5/8 (1) Washer, Lock #10 (1) Washer 3/16 x 3/4 x 16 Ga. (1) Nut, Weld #10 5 ASSEMBLY BEFORE YOU START TO ASSEMBLE THE GRASS CATCHER Some tractor models may need minor modifications before you can mount the grass catcher to the tractor. Look carefully at the drawbar on your tractor and compare to the illustrations below. If your drawbar looks like STYLE "A" (has the upper corner ribs), your tractor is ready - proceed with the grass catcher assembly. If your drawbar looks like STYLE "B" (does not have the upper corner ribs), go to the PREPARATION section in this manual. UPPER CORNER RIBS TRACTOR DRAWBAR STYLE "A" TRACTOR DRAWBAR STYLE "B" PARTS IDENTIFICATION UPPER CHUTE COVER er tain on en d. C wh alle placetainer. en qu em is pro fre lac g rep er taineck ba ed nd s con Ch me les n. om r un ioratio rec we ly a mo NINGand detier on e te Us era t WARop wear ged. no Do ject to dama or sub d cke cra is DUMP BAG INDICATOR CHUTE LATCH er tain on en d. C wh alle placetainer. en qu em is pro fre lac g rep er taineck ba ed nd s con Ch me les n. om r un ioratio rec we ly a mo NINGand detier on e te Us era t WARop wear ged. no Do ject to dama or sub d cke cra is er tain on en d. C wh alle placetainer. · Secure cover assembly to support tube using short hex bolt, long hex bolt, and locknuts as shown. NOTE: Hardware securing support tube to drawbar must be tightened at this time. · Install the four (4) tubing end caps onto container support. Tap each end cap onto container support tubes to seat securely. COVER SEAL SHORT HEX BOLT LONG HEX BOLT COVER ASSEMBLY LOCKNUTS FIG. 2 BRACKET SUPPORT PIN RETAINER SPRING 3 · · SUPPORT POST (See Fig. 3) Use Hardware - - GROUP "B" CAUTION: Container support is spring loaded and locked to the cover. Handle cover assembly carefully so as not to unlatch the cover from the container support. END CAP Rotate cover assembly onto its side as shown. Assemble support post to container support with the three (3) carriage bolts and locknuts. Tighten securely. CARRIAGE BOLTS LOCKNUTS SHORT HEX BOLT LONG HEX BOLT SUPPORT TUBE SUPPORT POST LOCKNUTS MOUNTING BRACKET LANCED TABS SUPPORT POST FIG. 4 ASSEMBLY 5 · · · · CONTAINER ASSEMBLY (See Fig. 5) No hardware required Place bottom half inside of top half, as shown. [. . . ] · Make sure the blade and all moving parts have completely stopped. · Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. NOTE ON SOME MODEL TRACTORS, MINOR MODIFICATIONS MAY BE NECESSARY TO MOUNT YOUR NEW GRASS CATCHER. NOT ALL MODEL TRACTORS WILL NEED THE FOLLOWING MODIFICATIONS. CHECK EACH STEP CAREFULLY TO DETERMINE IF MODIFICATION IS REQUIRED. [. . . ]