User manual JOYTECH AV CONTROL CENTER 2

[. . . ] The AV Control Center 2 has a total of 6 Input Channels. Input 6 is located on the front panel and Inputs 1 to 5 are located on the rear panel. Each Input Channel comprises of either 5 or 7 Input Connectors (figure. 1) CONTENTS Figure 1. Requires 2 x AAA (LR03) alkaline batteries. EXAMPLE OF A TYPICAL SETUP USING THE AV CONTROL CENTER 2 The AV Control Center 2 has been designed to connect up to 6 separate AV devices and output the Audio/ Video signal to a single input on the TV / Hi-Fi. [. . . ] Connect the SCART connector to a SCART Input Socket. Note: SCART will normally carry both the video and stereo audio signals. This is the most versatile AV connection and is recommended wherever possible. Connect the SCART connector to a SCART Input Socket and the digital optical connector to the Digital Optical Socket in the same Input Channel. Remember to remove the dust cap and store safely for when Optical Socket is not in use. Connect the Ethernet cable to an Ethernet Input Socket. Ethernet: Note: Your modem must either be a DSL or a cable modem. Do not use the AV Control Center 2 with a standard telephone modem. IMPORTANT: Before connecting your modem to the AV Control Center 2, make sure you have a valid account. Connect a composite video and mono/ stereo audio cable to the SCART Adapter and connect to any SCART Input Socket. Composite Video and Mono Audio: Composite Video and Stereo Audio: S-Video and Stereo Audio: PROGRAMMING THE INPUT CHANNEL DISPLAY SCART: For easy identification of the AV equipment connected to the AV Control Center 2 it is possible to name each of the 6 inputs on the Input Channel Display. For example should you wish Input 1 to read `DVD' and Input 2 to read `GAME', follow this setup procedure: 1) Using the Select Button on the front panel, select the desired Input Channel (1-6) that you would like to name. 2) Open the access cover on the front of the AV Control Center 2. 3) Press the SET Button to begin to change the name. The first character on the Input Channel Display will begin to flash. 4) Use the + and - buttons to cycle through all the available characters. When the desired character is displayed, press the SET Button to select the character and move to the next. Repeat the process until you have achieved your desired name. 5) Once you have selected the 5th character the name will be stored and assigned to your chosen Input Channel. Repeat the above procedure for each Input Channel you wish to name. SCART and Digital Optical: SCART Adapter: IMPORTANT: Each input connection will only correspond to the matching output connection except Input 6 (See below). For example a SCART cable attached to SCART Input 1 can only be viewed via the SCART Output Socket and cannot be displayed via the S-Video, Composite Video or Stereo Audio RCA Output Sockets. INPUT 6: The Composite Video and Stereo Audio RCA Input Sockets on Input 6 link directly to both the corresponding Output Sockets and the SCART Output Socket located on the rear panel of the unit. The S-Video Input Socket on Input 6 links directly to the S-Video Output Socket located on the rear panel of the unit. 6 7 AV_CONTROL_V1_ENG. qxq 22/11/04 11:33 am Page 8 ENGLISH TROUBLESHOOTING CAUTION: ENGLISH · Do not remove this product when the console power is ON. [. . . ] Seizures may also cause loss of consciousness or convulsions that can lead to injury from falling down or striking nearby objects. Immediately stop playing and consult a doctor if you experience any of these symptoms. Parents should watch for or ask their children about the above symptoms - children and teenagers are more likely than adults to experience these seizures. Taking the following precautions may reduce the risk of photosensitive epileptic seizures: · Sit further away from the screen · Use a smaller TV screen · Play in a well-lit room · Do not play when you are drowsy or fatigued If you or any of your relatives have a history of seizures or epilepsy, consult a doctor before playing. [. . . ]