User manual JOYTECH CONTROL CENTER 540C

[. . . ] Before using this product please familiarize yourself thoroughly with this User Guide so you fully understand the setup procedure and functions of the product. Note: Read your Xbox 360TM console Instruction Manual for important safety information and health warnings. Please retain both documents for future reference. Check that you have the following items: With faceplate removed 1) Control Center 540CTM 2) AV Interconnect Cable 3) Ethernet Cable 4) Remote Control 5) User Guide 6) Power Adapter 10 11 12 13 14 15 16 7 89 The Control CenterTM 540C has six A/V input channels which can be used to connect an Xbox 360TM console and up to five other AV devices to one TV. [. . . ] Use the display navigation buttons (< / >) to cycle through the letters until the letter you want is displayed. Press the green button to confirm the selection and move the next letter to change. 6) To save the new Input Channel name, push and hold down the green button for 3 seconds. Setting 5: SPEAKER The Control CenterTM 540C features an audible bleep for confirming selection of each Input Channel: (the sound can be set to either ON and OFF) Follow the above procedure to make required setting changes. Setting 4: BRIGHT Change the backlight level of the display screen: (two levels of brightness are available) Follow the above procedure to make required setting changes. The Hub is used for connecting to Xbox Live®, home networks and any other network enabled devices. NOTE: You must have a high-speed (cable or DSL) internet connection to play on Xbox Live®. 1) Connect the Ethernet Cable (supplied) to the Ethernet LAN port on the rear of your Xbox 360TM console and the other end of the Ethernet Cable to the port labeled IN1 on the Control CenterTM 540C Hub. 2) Connect an Ethernet Cable to the UPLINK port on the Control CenterTM 540C Hub and the other end of the Ethernet Cable to your high-speed modem. NOTE: You can connect other devices to the Ethernet Hub on LAN ports 2 - 5 The table below shows the status of the LAN port LED's during use. You can page through each Input Channel by pressing the Input Select Button on the front panel of the Control CenterTM 540C. Alternatively you can select each Input Channel by using the directional or numerical buttons on the Remote Control. Possible Solution Switch on by either pressing the Power / Standby Button at the front of the Control CenterTM 540C or by pressing the Standby Button on the Remote Control Switch on by either pressing the Power / Standby Button at the front of the Control CenterTM 540C or by pressing the Standby Button on the Remote Control Ensure that the Control Center is connected correctly to your Television. Plug another device into the same wall socket to confirm the outlet is working Ensure that the Control CenterTM 540C is connected correctly to your Television Wall outlet is not functioning The Control CenterTM 540C is on, but I do not see a picture from my TV No sound from speakers Ensure the correct video input on your TV has been selected (Refer to your TV instruction manual for more information) Make sure each AV device is connected to the Control CenterTM540C correctly AV devices incorrectly connected to Control CenterTM 540C Wrong device channel selected on Control CenterTM 540C The Control CenterTM 540C is on, but there is no sound from my TV Ensure you have selected the correct Input Channel on the Control CenterTM 540C S-video and Component connections carry picture information only Volume settings on your TV and AV devices are set too low When I view an AV device I get background interference Check that the connections between AV devices are secure Switch off any AV devices connected to the Control CenterTM 540C that are not in use Some AV devices can emit strong signals when left ON Incorrect use of batteries can result in battery leakage or explosion. When using batteries, be sure to follow these instructions: · Make sure that the plus and minus terminals of the batteries are inserted in the correct directions. Do not mix old and new or different types of batteries. Remove the batteries when the product will not be used for an extended period of time. If the battery has leaked, be sure to carefully remove all residue before inserting new batteries. These seizures may have a variety of symptoms, including lightheadedness, altered vision, eye or face twitching, jerking or shaking of arms or legs, disorientation, confusion, or momentary loss of awareness. Seizures may also cause loss of consciousness or convulsions that can lead to injury from falling down or striking nearby objects. Immediately stop playing and consult a doctor if you experience any of these symptoms. Parents should watch for or ask their children about the above symptoms - children and teenagers are more likely than adults to experience these seizures. [. . . ] Incorrect use of batteries can result in battery leakage or explosion. When using batteries, be sure to follow these instructions: · Make sure that the plus and minus terminals of the batteries are inserted in the correct directions. Do not mix old and new or different types of batteries. Remove the batteries when the product will not be used for an extended period of time. [. . . ]