User manual JRC NSVS1127

[. . . ] 2004 JRC SAW FILTER NSVS1127 Application 915. 0MHz(BW=26MHz) ISM Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig. 1. Item Input and Output Impedance Nominal Center Frequency (f0) Insertion Loss 902. 0~928. 0MHz Response Variation 902. 0~928. 0MHz Input and Output VSWR 902. 0~928. 0MHz Out of Band Rejection DC~800. 0MHz ( (Relative toThrough Level) 800. 0~845. 0MHz 845. 0~880. 0MHz 947. 0~992. 0MHz 992. 0~1020. 0MHz 1020. 0~1200. 0MHz Spec. [. . . ] Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -40ºC or more than +85ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max. , the time of soldering: 10 seconds max. , the power of soldering iron: 30W max. . Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. As it might be a cause of degradation or destruction to apply D. C. voltage between each terminal, apply D. C. [. . . ] 2004 IN 50 O *27nH 11 10 , X , W , U , V OUT 50 O 39pF 12 SAW 0 S21 FREQUENCY CHARACTERISTICS , P , Q , R , S 33pF , T *27nH 0 *murata LQW18A series Insertion Loss [dB] 10 Fig. 1 Measuring circuit 2 (1) 20 (a) 13. 30±0. 20 (b) (C) (1. 26±0. 13) 4 (2) 30 6 40 50 CH1 : center 915 span 200 CH2 : center 915 span 200 J4Y1 VS971 S11 6. 5±0. 20 8 10 S22 (3) (R0. 3) [4×] Marking (1) Manufacture's Mark (2) Lot Number (a) Year 2. 0 max. (b) Month *Oct. --- X Nov. --- Y Dec. --- Z S11 (0. 76) 11 9 S22 (2. 54) (2. 54) 11 9 (c) Date 1 --- 0 -9 10 -19 --- 1 20 -31 --- 2 (3) Part Number Mark VSWR 7 5 3 1 815 Frequency [MHz] VSWR 7 5 3 1 815 (2. 54±0. 15) 1015 (1. 4) [12×] Pin No. Connection 1 Frequency [MHz] GND(PKG) 1015 GND(PKG) GND(PKG) GND(PKG) OUT/IN GND(signal) GND(PKG) GND(PKG) GND(PKG) GND(PKG) IN/OUT GND(signal) 2 3 4 5 6 7 8 (0. 8) 0 InsertionLoss [dB] 20 12 40 1 2 3 4 5 (2. 54±0. 15) 60 11 10 80 100 0 9 8 7 6 [12 ×] S21 9 10 11 12 (R0. 3) [12×] 3000 Frequency [MHz] Fig. 2 Package dimensions(in mm) Japan Radio Co. , Ltd. Insertion Loss [dB] [. . . ]