User manual JRC NSVS1148

[. . . ] 2004 JRC SAW FILTER NSVS1148 Application 1220MHz Digital TV Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig. 1. Table 1. Input and Output Impedance 200 Nominal Center Frequency (f0) 1220MHz Insertion Loss 1216~1224MHz 4. 3dB max. 3. 0dB Response Variation 1216~1224MHz 1. 5dB max. [. . . ] 5 3) [ 4 x] Marking (1) Lot Number (a) Year (b) Month *Oct. --Nov. --Dec. --(c) Date *1-9--10-19--20-31--(2) Part Number Mark X Y Z 0 1 2 8 Fig. 2 Package dimensions (in mm) 1. 15 0. 93 3. 8 0. 6 1. 15 Via -Hole( 0. 3) Pin no. 1 2 3 4 5 6 7 8 Connection IN, Balanced IN, Balanced GND GND OUT, Balanced OUT, Balanced GND GND 0. 93 3. 8 0. 6 Fig. 3 Desirable land area (in mm) NSVS1148 Oct. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -20ºC or more than +70ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max. , the time of soldering: 10 seconds max. , the power of soldering iron: 30W max. . Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. As it might be a cause of degradation or destruction to apply D. C. voltage between each terminal, apply D. C. [. . . ] When intending to use any our product please contact our sales representatives in advance. NSVS1148 Oct. 2004 IN 50 O *27nH 11 10 , X , W , U , V OUT 50 O 39pF 12 SAW , P , Q , , T R *27nH , S 0 S21 33pF FREQUENCY CHARACTERISTICS *murata LQW18A series 0 Insertion Loss [dB] 10 2 (1) 13. 30±0. 20 20 (a) (b) (C) (1. 26±0. 13) 4 (2) 30 6 40 50 CH1 : center 1220 span 200 CH2 : center 1220 span 200 J4Y1 VS971 S11 6. 5±0. 20 8 10 (3) S22 (R0. 3) [4×] Marking (1) Manufacture's Mark (2) Lot Number (a) Year 2. 0 max. (b) Month *Oct. --- X Nov. --- Y Dec. --- Z S11 (0. 76) 11 9 (2. 54) (2. 54) 11 9 S22 (c) Date 1 --- 0 -9 10 -19 --- 1 20 -31 --- 2 (3) Part Number Mark VSWR 7 5 3 1 1120 Frequency [MHz] VSWR 7 5 3 1 1120 (2. 54±0. 15) 1320 (1. 4) [12×] Frequency [MHz] Pin No. Connection 1 2 3 4 5 6 7 8 1320 GND(PKG) GND(PKG) (0. 8) 0 [12 ×] S21 1 2 3 4 GND(PKG) GND(PKG) OUT/IN GND(signal) GND(PKG) GND(PKG) GND(PKG) GND(PKG) IN/OUT GND(signal) InsertionLoss [dB] 20 12 40 5 (2. 54±0. 15) 60 11 10 80 100 500 9 8 7 6 9 10 11 12 (R0. 3) [12×] 3000 Fig. 2 Package Frequency [MHz] mm) dimensions(in Japan Radio Co. , Ltd. Insertion Loss [dB] Fig. 1 Measuring circuit [. . . ]