User manual JUNO JGU4411

[. . . ] Children should not be allowed to tamper with the controls or play with the appliance. Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. This appliance should be serviced by an authorized Service Centre, and only genuine spare parts should be used. It is dangerous to alter the specifications or modify this appliance in any way. [. . . ] This will prevent it from becoming a death-trap for a child. Do not use detergents or abrasive powders, as these will damage the finish. Location Fig. 1 Positioning The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. ; best performance is obtained with ambient temperature between +18°C and +43°C (class T); +18°C and +38°C (class ST); +16°C and +32°C (class N); +10°C and +32°C (class SN). The class of your appliance is shown on its rating plate. For building into kitchen units follow the special "Building-in" instructions given. For safety reasons, minimum ventilation must be as shown in Fig. Attention: keep ventilation openings clear of obstruction. 450 547 550 This appliance is designed to be built-in to a space having the dimensions given in Fig. 1. 820 820-870 44 6 D506 100-170 870 Fig. 2 The height of the appliance can be altered if required by means of adjustable feet situated at its base (Fig. 2). Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage. For operation with different voltages, a suitably sized auto-transformer must be used. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician. The Manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with EEC directive number 87/308 of 2/6/87 relative to radio interference suppression. D507 Door reversibility Remove the two screws which fix the upper hinge to the door. Fig. 3 Carefully lean the appliance on its back and remove the plastic insert (Fig. 3). This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. D447 Remove the two screws which fix the lower hinge to the door. Remove the four screws which fix the lower hinge to the base of the appliance and remove the hinge itself; be very careful to recover all the screws. Remove the four screws that fix the upper hinge to the appliance and remove the hinge itself. Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. 13 Fig. 6 Take the hinge removed from the upper part of the appliance on the opposite side (see Fig. [. . . ] Do not use a mechanical device or any artificial means to speed up the defrosting process other than those recommended by the manufacturer. However, when the ice becomes very thick on the inner liner, complete defrosting should be carried out as follows: move the ON/OFF switch to OFF or pull out the plug from the wall socket; remove any stored food, wrap it in several layers of newspaper and put it in a very cool place; leave the door open; when defrosting is completed, dry the interior thoroughly; keep the scraper for future use; move the ON/OFF switch to ON or replace the plug in the power socket. Set the appliance to run on fast freeze; after 3 hours, set the switch back to normal operation. Important: A temperature rise of the frozen food packs, during defrosting, may shorten their safe storage life. 18 MAINTENANCE Unplug the appliance before carrying out any maintenance operation. [. . . ]