User manual JUNO JKU6331

[. . . ] JKU 6031 JKU 6331 GEBRAUCHSANWEISUNG OPERATING INSTRUCTIONS MODE D'EMPLOI GEBRUIKSAANWIJZING 2222 319-12/1 CONTENTS Warnings . page 12 13 13 13 13 14 14 14 16 17 17 17 17 17 17 18 18 18 19 19 19 19 19 Installation . Positioning . Electrical connection . . . Door reversibility Fitting a decorative door panel. Changing the opening direction of the door . [. . . ] For safety reasons, minimum ventilation must be as shown in Fig. Attention: keep ventilation openings clear of obstruction. This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. 13 Location Fig. 4 600 547 550 This appliance is designed to be built-in to a space having the dimensions given in Fig. 1. Take the hinge removed from the upper part of the appliance on the opposite side (see Fig. 4), and, using the screws removed from the lower part, fix it to the base of the appliance itself. D510 820 820-870 59 6 D506 100-170 870 Fig. 2 The height of the appliance can be altered if required by means of adjustable feet situated at its base (Fig. 2). Remove and refit the other hinge on the upper part of the appliance on the opposite side. Fix the two front screws into the upper and lower hinges (Fig. Finally, check the alignment of the door and make sure it closes properly. After having reversed the opening direction of the door, discard the original plastic insert removed and fit the insert supplied with the appliance on the opposite side. Fitting a decorative door panel D507 Door reversibility Remove the two screws which fix the upper hinge to the door. Fig. 3 Carefully lean the appliance on its back and remove the plastic insert (Fig. 3). Important: The components needed to fit the decorative panel have been pre-fitted on the appliance. The brackets are secured to the panel by means of the 7 Ø 3. 5x13 screws supplied. Before starting to fit the panel, remove the large top bracket by unscrewing the screws and adjusting pins pre-fitted on the appliance door. The small bottom bracket need not be removed. Fig. 5 A = = D447 Remove the two screws which fix the lower hinge to the door. Remove the four screws which fix the lower hinge to the base of the appliance and remove the hinge itself; be very careful to recover all the screws. Remove the four screws that fix the upper hinge to the appliance and remove the hinge itself. D467 Place the appliance in the position where it is to be built in (Fig. The appliance is fitted with adjustable feet; screw the front and rear feet in or out to adjust the height of the appliance to that of the recess. Keeping the appliance central in the recess, slide it in until its back touches the wall. With a tape measure (or similar instrument), measure distance (A) between the top edge of the door and the top edge of the decorative panel, placing it next to the recess. 14 Fig. [. . . ] Small pieces may even be cooked still frozen, directly from the freezer: in this case, cooking will take longer. (Only for model JKU 6331) The freezer compartment, however, will become progressively covered with frost. This should be removed with the special plastic scraper provided, whenever the thickness of the frost exceeds 4 mm. During this operation it is not necessary to switch off the power supply or to remove the foodstuffs. Never use sharp metal tools to scrape off frost from the evaporator as you could damage it. [. . . ]