User manual JUNO JMW2100-E

[. . . ] These warnings are provided in the interest of safety. You must read them carefully before installing or using the appliance. This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the appliance. [. . . ] The Manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with EEC directive number 87/308 of 2/6/87 relative to radio interference suppression. This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. 19 POSITIONING Height adjustment The height of the appliance is adjustable from 820 to 870 mm (Fig. 1) to line up with existing kitchen units. Fig. 1 Fitting the side panels Fit the brackets onto the panels in the positions shown in the diagram (Fig. The dimension of 132 mm is allowed for fitting a 100 mm plinth below the panel. For different plinth sizes, reduce or increase the dimension of 132 mm accordingly. REAR EDGE RIGHT HAND SIDE PANEL FRONT EDGE Fig. 3 15 820 870 820 Before installing the appliance between units, adjust the height of the feet and rear wheels. The wheels are factory set for a height of 820 mm. To align the appliance to a height of 870 mm, raise it by adjusting the feet with a spanner, then remove the wheels and refit them in the lowest position (Fig. 2 INSIDE FACE 1052 15 280 275 5765 541 20 132 820 Rest the panels against the appliance (Fig. The top of the appliance must be kept clear to allow better air circulation. If a wall unit is fitted above the appliance, there must be a gap of 50 mm between this unit and the wall and it must be at least 50 mm below the ceiling (Fig. 15 Once adjustment has been completed, open the doors and drill the door panels with a 2. 5 mm bit through the hole in the hinge; fix with the screws (Fig. 16 50 50 25 23 Fitting the plinth Alignment height of 820 mm If using a 140 to 170 mm plinth, make a cut-out as shown (Fig. If using a plinth higher than 100 mm but less than 140 mm, cut the height compensation strip supplied with the appliance to the required depth and fit it between the plinth and the ventilation grille, pressing it into position below this grille (Fig. If using a 100 mm plinth, fit the complete height compensation strip (Fig. 19 820 870 170 220 30 100 0 100 150 90 140 30 190 100 Alignment height of 870 mm If using a 190 to 220 mm plinth, make a cut-out as shown (Fig. If using a plinth higher than 150 mm but less than 190 mm, cut the height compensation strip supplied with the appliance to the required depth and fit it between the plinth and the ventilation grille (Fig. If using a 150 mm plinth, fit the complete height compensation strip (Fig. If the appliance is installed at the end of a row of units, insert foot E to hold the plinth in place (Fig. 20 E 24 OPERATION Control panel AB CD 4 -13°-1 5° -18°-2 1° -24° -26° S S E A = «Appliance in operation» light B = Freezer alarm light C = Freezer electronic thermometer D = Fast Freeze indicator (S) F G E = Main On/Off switch F = Freezer and Fast Freeze (S) temperature control knob G = Refrigerator temperature control knob Starting up Turn switch E until the pointer is opposite the «I» symbol (pilot lights A and B will come on). [. . . ] Packs may be placed next to or on top of each other. When buying frozen foods, get them home and into your freezer as quickly as possible. Packs which are damaged or show traces of moisture indicate that the product has not been stored at the correct temperature and that the food may have lost its original quality. Partially defrosted foods must never be re-frozen and must be consumed as quickly as possible. [. . . ]