User manual JUNO JVZ9491

[. . . ] JVZ 9491 GEBRAUCHSANWEISUNG OPERATING INSTRUCTIONS MODE D'EMPLOI GEBRUIKSAANWIJZING 2222 318-02 CONTENTS Warnings . Water in the refrigerator compartment Poor performance . page 18 19 19 19 19 20 20 20 21 23 24 25 25 25 25 25 26 27 27 28 28 28 29 29 30 30 30 30 30 31 31 31 31 31 TECHNICAL SPECIFICATION SUPPLY VOLTAGE AND FREQUENCY POWER DRAWN GROSS CAPACITY Refrigerator Freezer Superchill compartment 220/230 V 50 HZ 235 W 266 litres 96 litres 28 litres 12 kg/24 hours Refrigerator Freezer automatic automatic FREEZING CAPACITY DEFROSTING Printed on recycled paper 17 WARNINGS It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings. [. . . ] Open the bottom door and position shim E on the panel. Insert the top door panel through guide block F in the guide, resting the door panel on shim E (Fig. 5 TOP RIGHT-HAND FRONT PANEL 3 MIN TOP LEFT-HAND FRONT PANEL 1034 20 5 20 11 11 1052 BOTTOM RIGHT-HAND FRONT PANEL BOTTOM LEFT-HAND FRONT PANEL 444 MIN. 447 MAX. Carefully level the appliance before fitting the door panels. Open one of the two bottom doors and its hinge and insert the door panel through guide block A in the guide on the appliance door. Secure the panel with a screw in the vertical slot in the hinge (Fig. 8 561 577 C F E A E A Fit bottom guide block C using two screws and fix the hinge with a screw in the vertical slot (Fig. Close the door and check that the panel is positioned at the required height. 21 Fig. 11 G Fix the door panel to the top hinge with a screw in the vertical slot. Fit bottom guide block G using two screws and fix the hinge with the screw in the vertical slot (Fig. Repeat these operations for the other top door. Check the horizontal alignment of the door panels and adjust if necessary (Fig. Re-open the door and drill with a 2. 5 mm bit in the centre of the horizontal slots in the hinge. Fix with the screws and remove those from the vertical slot (Fig. Check the vertical alignment of the doors and correct their position if necessary (Fig. 10 Level the front faces of the door panels by slackening the guide block screws and inserting the shims supplied, as necessary (Fig. 14 Building the appliance in Fit the appliance into the recess. Fix it to the wall with the appropriate bracket (Fig. The top of the appliance must be kept clear to allow better air circulation. If a wall unit is fitted above the appliance, there must be a gap of 50 mm between this unit and the wall and it must be at least 50 mm below the ceiling (Fig. 15 Once adjustment has been completed, open the doors and drill the door panels with a 2. 5 mm bit through the hole in the hinge; fix with the screws (Fig. 16 50 50 25 23 Fitting the plinth Alignment height of 820 mm If using a 140 to 170 mm plinth, make a cut-out as shown (Fig. [. . . ] Never consume products after the date shown on the pack. In the event of a short power cut, foods will not be affected, but you should avoid opening the appliance doors. 28 Ice cube maker Fill the ice cube trays to no more than 3/4 of their depth, to allow for expansion of the ice. To remove the ice cubes, simply turn the knob fully as shown in Fig. 24 Thawing food Foods may be thawed in various ways, depending on their type and the size of pack. [. . . ]