User manual JVC CA-MXKC2B

[. . . ] COMPACT COMPONENT SYSTEM CA-MXKC2 INSTRUCTIONS LVT1346-002A [B] Warnings, Cautions and Others IMPORTANT for the U. K. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. [. . . ] Therefore, the use of Non-DVD side of a DualDisc on this product may not be recommended. 13 Using the CD Player About Disc Indicator: Selected Disc indicator Disc Number indicator Disc Rotation indicator To Unload CDs Take out the CD as shown below. 1 2 3 4 The Disc indicator consists of the following three kinds of indicators: Disc Number indicator: Lights all the time. Selected Disc indicator:Lights for the currently selected disc number. Disc Rotation indicator:Runs when the selected CD is playing. This indicator goes out if a CD is not loaded for the selected disc number. While the CD Player is stopped, press the CD Open/Close 0 button on the Unit to open the tray. Remove the CD, then press the DISC SKIP button on the Unit. The tray turns for the next CD. Repeat step 2 to remove all the CDs. Press the CD Open/Close Unit to close the tray. 0 button on the One Touch Play The power comes on, and operations are done automatically. By pressing the CD 6 button, the System will come on, and if a CD is loaded for the disc number that was lastly selected, it will start playing from the first track. By pressing the CD1-CD3 button, the System will come on, and if a CD is already loaded for the selected disc number, it will start play from the first track. You can remove CDs while listening to the other source. Tips: Removing/changing the CDs during playback While playing back a CD (e. g. CD1), you can remove or change the other CDs (e. g. CD2 and CD3) by pressing the CD Open/Close 0 button. After removing or changing, press the same button to close the tray. Changing the MP3 Playback Mode When playing an MP3 disc, you can choose the playback mode of the MP3 disc as follows: To Load CDs 1 2 Press the CD Open/Close Unit to open the tray. 0 button on the Normal (FILE) mode: The unit recognizes only tracks (files). You can play an MP3 disc like an Audio CD. GROUP (ALBUM) mode: The unit recognizes tracks (files) and albums (folders) on an MP3 disc. You can play an MP3 disc according to the way how they are grouped. Place one or two CDs, with its label side up, onto the tray. Be sure that the CD is securely seated inside the recess on the disc tray. With the label side up On the Remote Control ONLY: Press MP3 before or during playing an MP3 disc. GROUP indicator appears when the MP3 playback mode is the GROUP mode. Each time you press the button, the MP3 playback mode changes between "GROUP (ALBUM)" and "Normal (FILE)" alternately. 3 4 Press the DISC SKIP button on the Unit and place the next CD. When you press the button, the tray turns for the next CD. Press the CD Open/Close Unit. 0 button on the The tray is closed. When you use an 8 cm CD, place it on the inner circle of the tray. You can load CDs while listening to the other source or while listening to the CD being played back. When power is turned off with the tray opened, the tray is automatically closed. If the CD cannot be read correctly (because it is scratched, for example), the CD is recognized as no disc. 14 English Using the CD Player English Basics of Using the CD PlayerNormal Play To Play CDs For MP3 disc Total track number 1 2 Load CDs. Press CD 6 button to play. To pause, press the CD 6 button. The playing time indication blinks on the display. To cancel pause, press the CD 6 button again. Play continues from the point where it was paused. Tips: Playing back the CD using the DISC SKIP button You can also play the CDs using the DISC SKIP button. [. . . ] Headphones are connected. Action Check all connections and make corrections. (See pages 4 to 6. ) Disconnect the headphones. Change the position and direction of the AM (MW) Loop Antenna. Extend FM Wire Antenna to the best reception position. [. . . ]