User manual JVC DLA-HD750BU

[. . . ] ENGLISH FRANÇAIS ESPAÑOL/CASTELLANO Getting Started INSTRUCTIONS MANUEL D’INSTRUCTIONS MANUAL DE INSTRUCCIONES D-ILA PROJECTOR PROJECTEUR D-ILA PROYECTOR D-ILA DLA-HD750 DLA-HD750 1108TTH-AO-AO DLA-HD750 Preparation D-ILA PROJECTOR PROJECTEUR D-ILA PROYECTOR D-ILA Basic Operation Settings Troubleshooting For Customer use : Enter below the serial No. which is located on the side of the cabinet. Retain this information for future reference. DLA-HD750 Pour utilisation par le client : Entrer ci-dessous le N° de série qui est situé sous le boîtier. [. . . ] Select the color to be adjusted in the gamma adjustment screen. Settings Picture Adjust > Gamma Normal A B C Costom1 Costom2 Costom3 Correction Value 1023 White Red Geen Blue 512 Copy Paste Reset 0 50 100(%) 2. 2 Exit MENU Select Operate Back BACK Check TEST Before ③ Adjust the gamma curve in the gamma curve adjustment screen. Troubleshooting Picture Adjust > Picture Adjust > Gamma Normal A B C Costom1 Costom2 Costom3 Correction Value 1023 White Red Geen Blue 512 Copy Paste Reset Input: 10% Output:100 0 50 100(%) Gamma Normal A B C Costom1 Costom2 Costom3 Correction Value 1023 White Red Geen Blue 512 Copy Paste Reset Input: 50% Output: 580 0 50 100(%) 2. 2 2. 2 Exit MENU Select Back Check Back TEST BACK Operate Before Exit MENU Select Back Check Back TEST BACK Operate After Select the point where the gradation (brightness) is to be adjusted with the / buttons. Adjust the gradation (brightness) with the / buttons. ● You can switch between “Before” and “After” using the [TEST] button of the remote control. ④ To end Others BACK BACK Save gamma data?Yes No OK ● If gamma curve is adjusted repeatedly, calculation errors will be accumulated and the gamma curve may not be able to revert back to its original form. In that case, select “Reset”. 33 4 Settings Setting Menu (Continued) Picture Adjust 08 Advanced in “THX”. ) Sharpness Sharpness Detail Enhancement RNR NR* MNR BNR Off CTI* Low Middle High * In case of HD signals or PC signals, NR and CTI cannot be set. (Soft) 0 to 100 (Sharp) (Soft) –50 to 50 (Strong) (Soft) 0 to 16 (Strong) (Soft) 0 to 16 (Strong) On Off Adjusts the outline of image. Adjusts the intensity of removing image noise. Adjusts the intensity of removing mosquito noise. Adjusts the contours of the image, detailed composition of the image and image color. (Cannot set when the “Picture Mode” ● Abbreviations NR: Noise Reduction RNR: Random Noise Reduction MNR: Mosquito Noise Reduction BNR: Block Noise Reduction CTI: Color Transient Improvement Off The image color cannot be adjusted. Custom 1 Custom 2 Custom 3 Pause Color Management Adjustment* All Reset Off On Video mode Still mode Color Management Values of each color can be adjusted (“Red, Yellow, Green, Cyan, Blue and Magenta”). Return to the factory settings. 09 Lens Aperture (Dark) -15 to 0 (Bright) 10 Reset Reset the setting. * About “Color Management Adjustment” 1 Set the picture mode of the color management. 2 Select the color to be adjusted by color management. Picture Adjust > Color Management Off Pause Custom1 Red Yellow Custom2 Green Custom3 Cyan Blue Magenta All Reset Hue Saturation Brightness Exit MENU Off 0 0 0 BACK Select Operate Back Check TEST Before 3 Select color adjustment. Picture Adjust > Color Management Off Custom1 Custom2 Custom3 Pause Red Yellow Green Cyan Blue Magenta All Reset Hue Saturation Brightness Exit MENU Off 0 0 0 BACK Select Operate Back Check TEST Before 34 ENGLISH Getting Started 4 Select the “Hue”, “Saturation” or “Brightness” using the 5 Use the / button to adjust. / button. Hue 7 Check TEST After ● You can switch between “Before” and “After” using the [TEST] button of the remote control. 6 To end Preparation BACK BACK BACK Save Color Management?Yes No OK Input Signal > HDMI 11 HDMI Configures HDMI input signal. Auto Input Standard Enhanced Auto Color Space YCbCr(4:4:4) YCbCr(4:2:2) RGB Control with HDMI On Off Automatically configures the input signals. Select this when the dynamic range of the input images is 16-235. Select this when the dynamic range of the input images is 0-255. Automatically configures the input signals. Select this when the Y Cb Cr(4:4:4) video signals are input. Select this when the Y Cb Cr(4:2:2) video signals are input. Select this when the RGB video signals are input. Disables CEC communications. Basic Operation Settings ● The setting is available only if the HDMI terminal is selected. [. . . ] Please consult your authorized dealer for replacement. 56 ENGLISH Getting Started Mounting this Unit Measures to prevent the unit from toppling or dropping should be taken for safety reasons and accident prevention during emergencies including earthquakes. When mounting this unit on a pedestal or ceiling, remove the 4 feet on the bottom surface and use all the 4 screw holes (M5 screws) to mount. Preparation Ceiling ■ Bottom Surface 4 locations Air inlets Basic Operation Air inlets SYNC Settings Precautions for Mounting ● Special expertise and techniques are required for mounting ● ● ● this unit. Be sure to ask your dealer or a specialist to perform mounting. Depth of the screw holes (screw length) is 23 mm. [. . . ]