User manual JVC GM-V42C-GM-V42 Instruction Manual

[. . . ] PLASMA DISPLAY MONITOR GM-V42UG GM-V42UB INSTRUCTIONS For Customer Use: Enter below the Model No. which is located on the rear panel of the cabinet. Retain this information for future reference. Model No. Serial No. MENU INPUT POWER LCT1389-001B INSTRUCTIONS Model GM-V42UG GM-V42UB Thank you for purchasing this JVC Monitor. Before using the monitor, read this manual carefully so that you know how to use the Monitor correctly. [. . . ] To cancel the reset, press MENU/EXIT (or MENU on the Monitor). reset See "To make an adjustment while viewing the adjustment bar" on the next page. See "To reset the adjustments" on the next page. Adjusting the Screen Size and Position The screen size and position can be adjusted. Adjusted settings can be stored for each signal type; therefore, when the same signal comes in, the stored settings are recalled. · When adjusting the size, the size cannot be adjusted proportionally, but can be enlarged rightward (or downward) only and reduced leftward (or upward) only. Therefore, it is necessary to adjust both the size and position alternately to adjust to the appropriate size. 1 Press MENU/EXIT (or MENU on the Monitor) to display the Main Menu. MAIN MENU *1 Size and position adjustments are so related that if one is adjusted much, the other's adjustable range will be reduced. *2 DOT CLOCK is the function to adjust the pixel sampling number of the A/D converter to the resolution (the vertical pixel number) of the input signal. CLOCK PHASE is the function to adjust the sampling timing (phase) to the phase of the input signal. You can use the two functions to reduce flickering and blurring on the screen when using the RGB A or RGB B input. 5 Press 2/3 to adjust the selected item. Note: · During size and position adjustments, the Monitor screen may be distorted. This is normal, but not a malfunction of the Monitor. Cursor (3) PICTURE ADJ. FUNCTION SELECT STATUS DISPLAY ENTER: SELECT: EXIT: MENU 2 Press 5/ to move the cursor (3) to "SIZE/POSITION ADJ. " 6 Press MENU/EXIT (or MENU on the Monitor) twice to exit from the menu operations. (To be continued on the next page) 17 Video Adjustments (Continued) To make an adjustment while viewing the adjustment bar After step 3 on page 17, proceed as follows: 1 Press 5/ to move the cursor (3) to "sub menu. " 2 Press 3 to display the Sub Menu. The Sub Menu for H SIZE appears on the screen. H SIZE ++ :+01 ++ MENU INPUT POWER 3 Press 5/ to select the Sub Menu you want to adjust. Each time you press the button, the Sub Menu changes as follows: H SIZE H POSITION V SIZE CLOCK PHASE DOT CLOCK V POSITION 4 Press 2/3 to adjust the selected item. 5 Repeat steps 3 and 4 to adjust the other items. 6 Press MENU/EXIT (or MENU on the Monitor) three times to exit from the menu operations. MENU INPUT POWER To reset the adjustments After step 3 on page 17, proceed as follows: 2/3 5 A B MUTING 5/ MENU 1 Press 5/ to move the cursor (3) to "reset. " 2 Press 3. The confirmation screen appears. reset Are you sure?"YES" then "NO" then MENU key. 3 Press 3 again to reset the adjustments. To cancel the reset, press MENU/EXIT (or MENU on the Monitor). Note: · Adjustment values for both horizontal and vertical sizes of the screen are so related that if one is adjusted up to near the maximum value, the attainable value of the other will be decreased. RM­C579 REMOTE CONTROL UNIT OFF DISPLAY POWER ON ASPECT INPUT SELECT COMPO. /(RGB B) VIDEO RGB A VOLUME MENU/EXIT MENU/EXIT 18 5 2/3 5/ Adjusting the Color Temperature The adjusted setting applies to all inputs. Adjusting the White Balance G GAIN, B GAIN and R GAIN can be finely adjusted separately for "HIGH" and "LOW" settings of the color temperature. 1 Press MENU/EXIT (or MENU on the Monitor) to display the Main Menu. MAIN MENU 1 Cursor (3) PICTURE ADJ. FUNCTION SELECT STATUS DISPLAY On the remote control: Press MENU/EXIT while holding VOLUME ­ to display the Setup Menu. On the Monitor: Press MENU while holding 2 to display the Setup Menu. SET-UP MENU 1/2 : : : : OFF OFF ENTER: SELECT: EXIT: MENU 2 3 Press 5/ to move the cursor (3) to "FUNCTION SELECT. " Press 3 to display the Function Selection Menu. FUNCTION SELECT COLOR TEMP. reset : : : : : H I G H* PANORAMIC AUTO RGB HIGH Cursor (3) STATUS DISPLAY CONTROL LOCK REMOTE SWITCH HD SIGNAL MODE WHITE BALANCE TIMER MODE1 1080i ADJUST: SELECT: EXIT: MENU ADJUST: SELECT: EXIT: MENU " * " appears only when you have adjusted the White Balance (see the right column). 2 Press 5/ to move the cursor (3) to "WHITE BALANCE. " · The Setup Menu consists of two pages. [. . . ] ­ After cleaning, switch on the Monitor's main power again. If self-diagnostic lamps do not go off, consult your dealer immediately. Note: If you switch on the main power immediately after switching it off (or after recovering from a brief power interruption), the self-diagnostic lamps may light (or flash), and no image may appear on the screen. In this case, switch off the main power again, wait for about 10 seconds, then switch it on again. If no self-diagnostic lamps light or flash, you can operate and use the Monitor as usual. Self-diagnostic Report Sheet Store name where you purchased the Monitor If the screen monitor dims a little and "TEMP. [. . . ]