User manual JVC HR-DD868

[. . . ] ENGLISH CONTENTS SAFETY FIRST INSTALLING YOUR NEW RECORDER INITIAL SETTINGS 2 3 4 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Basic Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 VIDEO CASSETE RECORDER HR-DD868EU FIRST SEE AUTO SET-UP ON BACK Auto Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Preset Download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Recording a programme of 210 minutes in length onto a 180minute tape OK Approximately 150 minutes SP mode Total 210 minutes Approximately 60 minutes LP mode MENU Make sure you set "AUTO SPLP TIMER" to "ON" at the Mode Set screen before the timer-recording starts. Auto Timer When the Auto Timer is set to ON the timer is automatically engaged when the recorder power is turned off and automatically disengaged when the recorder is powered back on. 1 2 3 4 ACCESS MAIN MENU SCREEN Press MENU. 1 2 3 4 ACCESS MAIN MENU SCREEN Press MENU. Press %fi to move the highlight bar (pointer) to "MODE SET", then press OK or #. ACCESS MODE SET SCREEN Press %fi to move the highlight bar (pointer) to "AUTO SPLP TIMER", then press OK or # to select "ON". SELECT MODE MODE SET B. ON PICTURE CONTROL AUTO AUTO TIMER OFF O. ON DIRECT REC ON AUTO SP=LP TIMER ON POWER SAVE OFF NEXT PAGE [5] = [MENU] : EXIT Press %fi to move the highlight bar (pointer) to "MODE SET", then press OK or #. ACCESS MODE SET SCREEN MAIN MENU MODE SET AUTO CH SET MANUAL CH SET INITIAL SET REC LEVEL CTL T [5] = [MENU] : EXIT RETURN TO NORMAL SCREEN Press MENU. NOTES: Press %fi to move the highlight bar (pointer) to "AUTO TIMER", then press OK or # to select either "ON" or "OFF". SELECT MODE MODE SET B. ON PICTURE CONTROL AUTO AUTO TIMER ON O. ON DIRECT REC ON AUTO SP=LP TIMER OFF POWER SAVE OFF NEXT PAGE [5] = [MENU] : EXIT RETURN TO NORMAL SCREEN Press MENU. If you have programmed the recorder to timer-record 2 or more programmes, the second programme and those thereafter may not fit on the tape if you set "AUTO SPLP TIMER" to "ON". In this case, make sure the mode is not engaged, then set the tape speed manually during timer programming. In order to ensure that the recording fits on the tape, this feature may leave a slight non-recorded section at the end of the tape. There may be some noise and sound disturbance at the point on the tape where the recorder switches from SP to LP mode. The Auto SPLP Timer feature is not available during ITR (Instant Timer Recording), and the feature will not work properly with any tapes longer than E-180 or with some tapes of shorter lengths. If you perform timer recording with both VPS/PDC and the Auto SPLP Timer activated, and the programme goes beyond its originally scheduled length, there may be times when the programme cannot be recorded in its entirety. NOTE: For safety, when Auto timer is set to "OFF", all other recorder functions are disabled while the Timer mode is engaged. To disengage the timer, press (TIMER). 32 EN TIMER RECORDING (cont. ) This facility allows you record automatically a satellite programme which is timer-programmed on your external satellite tuner. Connect a satellite tuner to the recorder's AV2 IN/DECODER connector ( pg. 44, 45) and programme the timer on the satellite tuner; the recorder starts recording when the signals input from the satellite tuner to the AV2 IN/DECODER connector, and when there is no input signals the recorder stops recording and the power shuts off. Before performing the following steps: Make sure the satellite tuner is connected to the recorder's AV2 IN/DECODER connector. 44, 45) Programme the timer on the satellite tuner. Insert a cassette with the safety tab in place. Automatic Satellite Programme Recording K RE C LI N 1 2 SELECT AV2 SELECT MODE Set "AV2 SELECT" to "AV2" ( pg. When you select "SAT", refer to "IMPORTANT" on page 44. SET TAPE SPEED Press SP/LP ( ) to set the tape speed. ATTENTION Be sure not to turn on the satellite tuner before the programme is executed; otherwise, the recorder will start recording when the satellite tuner's power is turned on. If you have connected another appliance other than a satellite tuner to the AV2 IN/DECODER connector, be sure not to engage the Auto Satellite Prog Rec mode; otherwise, the recorder will start recording when the connected appliance's power is turned on. Auto Satellite Prog recording and timer-recording cannot be done at the same time. 3 ENGAGE AUTO SATELLITE PROG REC MODE Press and hold REC LINK on the recorder for about 2 seconds. The button lights up and the recorder turns off automatically. To disengage the Auto Satellite Prog Rec mode, press REC LINK. If the recorder's power is off, it is not possible to engage the Auto Satellite Prog Rec mode. NOTES: Auto Satellite Prog recording is possible with the AV2 IN/DECODER connector only. [. . . ] 34) How To Use The remote control can operate most of your video recorder's functions, as well as basic functions of TV sets and satellite tuners of JVC and other brands. 34, 35) Point the remote control toward the sensor window. The maximum operating distance of the remote control is about 8 m. TV ­ TV TV PROG ­ Y NOTES: When inserting the batteries, be sure to insert in the correct directions as indicated under the battery cover. If the remote control doesn't work properly, remove its batteries, wait a short time, replace the batteries and then try again. EN 65 Remote Control LCD The remote control can operate not only the video recorder but also some of your TV and satellite tuner's functions. [. . . ]