User manual JVC HR-XVC25UC-HR-XVC25 Instruction Manual

[. . . ] DVD/CD PLAYER Hi-Fi STEREO VIDEO CASSETTE RECORDER USER'S GUIDE For model: HR-XVC25U For Customer Use: Enter below the Model No. which are located on the rear of cabinet. Retain this information for future reference. Model No. Serial No. LPT0837-001B CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] Press REC on the VCR again to the Remote to stop recording after 30 minutes. Each additional press of REC will increase recording time as shown in the chart below, up to a maximum of 6 hours. The ITR and recording time will appear on the screen for about 4 seconds. And, REC will keep blinking in the display. Press Recording time NORMAL REC once twice 0:30 3 times 1:00 4 times 1:30 5 times 2:00 Press Recording time 3:00 6 times 4:00 7 times 5:00 8 times 6:00 9 times 10 times NORMAL REC ITR 0 : 30 CH 125 INDEX NOTE: If you wish to watch the DVD playback during the ITR, press DVD to change to DVD mode and perform the DVD playback (see page 39). To cancel ITR Press STOP or turn off the power. " " will appear on screen for about 4 seconds. 32 Timer recording Timer recording can be programmed on-screen with the remote control. The built-in timer allows automatic unattended recording of up to 8 programs within 1 month. Preparation: Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Load a cassette tape with the erase prevention tab intact. Press OSD to verify time and date are correct (see page 31). Example: Program a timer recording for the 26th day, channel 125 (CATV), 11:00 - 11:30 PM on timer program number 1 (Tape speed: EP). Select the REC SET option, then press ENTER. MENU TIMER REC SET AUTO REPEAT ON OFF ON OFF SAP CH SETUP SYSTEM SETUP +//ENTER/MENU select one of 2 Press SET + or topress ENTER. the program line, then DATE START END : : : : : : : : : : : : : : : : CH +//ENTER/CANCEL/MENU SET + or to 3 Presspress ENTER. select the date, then DATE START END CH 26(SU) : : : : : : : : : : : : : : : : +//ENTER/CANCEL/MENU time, 4 Set the start time, endstep 3. channel and tape speed as in NOTES: NOTES: If the clock symbol ( ) blinks when the timer recording ended, the TV program has not been completely recorded because of an insufficient tape supply. In this case, press TIMER to cancel the timer program or press EJECT to remove the cassette tape. During timer recording standby mode, the VCR mode cannot be selected. To use the VCR, press TIMER at first, then press VCR to change to VCR mode. After you use the VCR, press TIMER again to put the VCR into timer recording standby mode. If you press TIMER during timer recording, the recording operation will be interrupted. If you press TIMER again within the programmed time, the recording operation will start again. After a power failure or disconnection of the power plug, all programmed recording settings and time display will be lost upon resumption of power. In this case, reset the clock (see pages 23-25) and reprogram any timer recordings. DATE START END CH 26(SU) If the programmed start time is over the present time, the program will be canceled +//ENTER/CANCEL/MENU after pressed ENTER. [. . . ] Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. All products and parts thereof may be brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and above which are covered on an in-home basis. WHAT YOU MUST DO FOR WARRANTY SERVICE: Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service center, please call toll free: (800) 537-5722. [. . . ]