User manual JVC JX-S333

[. . . ] AV SELECTOR SELECTEUR AV SELECTOR AV JX-S333 POWER SOURCE SELECT 1 2 3 4 DUBBING LOCK (MONITOR SELECT) LINK STAN DB Y/O N 1 2 SOU CT 3 4 (MO DUBB ING LOCK NITO R SE LECT ) LINK MANUEL D'INSTRUCTIONS MANUAL DE INSTRUCCIONES For Customer Use: Enter below the Serial No. which is located on the rear or bottom of cabinet. Retain this information for future reference. JX-S333 LNT0042-001A OTHERS INSTRUCTIONS ADVANCED OPERATION RCE SELE BASIC OPERATION INTRODUCTION ESPAÑOL FRANÇAIS ENGLISH Safety Information FCC INFORMATION This device complies with Part 15 of the FCC Rules. [. . . ] Incoming signals from these connectors are emitted through all the output connectors at the same time. DO NOT connect the input connectors of the components connected to these connectors to any of the output connectors of the JX-S333. 10 -EN POWER SOURCE SELECT 1 Turning the power on 2 Selecting a VCR Press 1. ON onPOWER (orunit) STANDBY/ the main to turn on the JX-S333. · The STANDBY/ON indicator lights in green. POWER 1 2 3 4 DUBBING LOCK (MONITOR SELECT) LINK 2. Press SOURCE SELECT "1" to select VCR1. · The indicator lights in red. 1 1 SOURCE SELECT · If the SOURCE SELECT "1" indicator on the JX-S333 is already lit, it is not required to press the SOURCE SELECT "1" button. DUBBING LOCK 4 ANDBY/ON ST 1 2 3 (MONITOR SELECT) LINK 2 · Turn the TV monitor on and select the input connected to the MONITOR OUT connectors on the JX-S333. VCR PLAY · When you want to watch a video on another VCR, press the SOURCE SELECT button to select the line number that the VCR is connected to. · Using the LINK function, you can turn on and off the power to the JX-S333 by detecting the incoming S-video signals ( P. 20). EN- 11 OTHERS ADVANCED OPERATION 4. Turn on the VCR's power and start playback. BASIC OPERATION the TV 3. monitor on and select the INTRODUCTION ENGLISH Dubbing (Multi-dubbing) Do not connect the AC power cord until all other connections have been made. You can dub a video program from VCR 1 to VCR 2 and vice versa. This shows an example of several possible connections. Also refer to the instruction books of the other components you are using for operation and connection details. VCR1 (Playback component) To S-VIDEO Output To AUDIO Output To Component Video Output To S-VIDEO Input To AUDIO Input (green) (white) (white) (blue) (red) (red) (red) : Signals from VCR 1 to VCR 2 : Signals from VCR 2 to VCR 1 (green) (white) (white) (blue) (red) (red) (red) To Component Video Input JX-S333 rear panel (green) (blue) (red) (green) (blue) (red) To AUDIO Input (white) (white) (red) TV monitor (green) (white) (white) (blue) (red) To Component Video Output (red) (red) (red) To S-VIDEO Input To S-VIDEO Input To AUDIO Output To AUDIO Input To S-VIDEO Output (green) (white) VCR2 (Recording device) Connection tips · Before making any connections, turn off the power to all components. · It is not required to connect the components using both SVIDEO and component video connectors. To obtain the best possible playback picture on the TV monitor, connect the component using the component video connectors. However, to dub the tapes, it is required to connect the playback components through the S-VIDEO connectors. · If both the S-VIDEO and component video connectors are connected between the components, the incoming signals are emitted through the respective output connectors. 7 "Video input/output signals") (white) (blue) (red) (red) (red) · The INPUT 1 and INPUT 2 connectors are used for connecting the playback/recording components. Incoming signals from the INPUT 1 and INPUT 2 connectors are emitted through the MONITOR OUT connectors and at the same time. . . ­ Signals from the INPUT 1 connectors are emitted through the OUTPUT 2 connectors. ­ Signals from the INPUT 2 connectors are emitted through the OUTPUT 1 connectors. 12 -EN Preparation POWER SOURCE SELECT 1. Press SOURCE SELECT "1" to select VCR1 as the source component. · The indicator lights in red. 1 2 3 4 1 Selecting VCR 1 1 DUBBING LOCK (MONITOR SELECT) LINK · If the SOURCE SELECT "1" indicator on the JX-S333 is already lit, it is not required to press the SOURCE SELECT "1" button. 2. Play back a tape on VCR 1. VCR 1 PLAY SOURCE SELECT DUBBING LOCK 4 ANDBY/ON ST 1 2 3 (MONITOR SELECT) LINK VCR 2 1 Notes: Notes REC Notes: · Some video software may contain signals to prevent it from being copied. If you try to copy such a program, the results will not be viewable. · Recording of copyrighted material for purposes other than personal use is illegal without permission of the copyright holder. EN- 13 OTHERS To prevent erroneous operation during dubbing, press the DUBBING LOCK button to activate the DUBBING LOCK function ( P. 19). ADVANCED OPERATION · Set the input switch on the recording VCR to the external input mode (AUX) when dubbing. · Set the recording VCR to S-VIDEO input when using an S-VIDEO input connector for recording. BASIC OPERATION 3. Start recording on VCR 2. INTRODUCTION ENGLISH · Turn on the power to the JX-S333. · Turn on the TV monitor and select the input connected to the MONITOR OUT connectors on the JX-S333. · Turn on the power to VCRs to prepare for dubbing. Watching a Video Program While Recording Another One (Dubbing Lock) Do not connect the AC power cord until all other connections have been made. [. . . ] 13 13 · Some video software may contain signals to prevent it from being copied. If you try to copy such a program, the results will not be viewable. Dubbing operations are not possible when using equipment connected to the component connector. ·Are the S-VIDEO connectors also connected? -- · Component video signals cannot be 12, 14 converted into S-video signals. [. . . ]