User manual JVC KSK6012J-KS-K6012 Instruction Manual

[. . . ] JVC is not responsible for issues arising from installations not performed according to the procedures in this manual. · Do not install the unit where it may obstruct your view through the windshield or of your vehicle's indicator displays. · Do not install the unit where it may hinder the function of safety devices such as an airbag. [. . . ] If anything is missing or damaged, or if your Car Docking Kit fails to operate, notify your shipper immediately. It is recommended that you keep the original packaging in case you need to ship your Car Docking Kit in the future. 4 Installation in Your Car CAUTION: Do not put JVC PnP in the car docking cradle until you have completed the installation. 1 Determine where you want to mount JVC PnP. · Do not install JVC PnP where it may obstruct your view through the windshield or your view of your car's indicator displays. · Do not install JVC PnP where it will hinder your access to the car's controls. · Do not install JVC PnP where it may hinder the function of safety devices such as an airbag. Doing so may prevent the airbag from functioning properly in the event of an accident. · Find a location that provides good visibility of and access to JVC PnP's front panel. 2 Assemble the supplied suction cup mount to JVC PnP using the supplied screws. · When using other screws, use the screws of less than 8 mm (3/8 inch) long with a diameter of 4 mm (3/16 inch). To be continued. . . 5 Installation in Your Car (Continued) CAUTION: Do not plug the cigarette lighter adapter into the cigarette lighter until you have completed the installation. 3 Plug the cigarette lighter adapter into the back of the cradle--DC 12 V. Back of the cradle 4 Activate the FM signal transmitter and preset the frequency (refer to "4 FM Transmitter Options" on page 24 of KT-SR2000 Instructions). · It is recommended to preset the same frequency into your car stereo as you have selected so you can easily tune in to the frequency. ANT. DC 12V FM OUT AUDIO Note: You can also connect a cassette adapter or an audio cord (both not supplied) to the AUDIO jack to send the signals to your car stereo. An optional hard-wired FM transmitter--FM Switching Box Assembly (Parts No. By connecting this Assembly between the FM OUT terminal of the cradle and the antenna input terminal of your car stereo, you can obtain stable and reliable transmission/reception. 6 Finding the Best Antenna Mounting Location 1 Temporarily plug the antenna into the back of the cradle--ANT. Back of the cradle 3 4 Temporarily plug the cigarette lighter adapter into the cigarette lighter. Slide JVC PnP all the way into the cradle so that the connector at the bottom of the unit makes proper contact in the cradle. ANT. DC 12V FM OUT AUDIO 2 Find an antenna location on a metal surface of your car--at least 30 cm × 30 cm (12 inches × 12 inches), and at least 15 cm (6 inches) from a window. · The antenna's powerful magnet will secure it to the metal surface. · Best reception is achieved with the antenna mounted on the roof or trunk for convertibles. · If your car has a roof rack or skid ribs, it may be necessary to mount the antenna off-center. To be continued. . . 7 Finding the Best Antenna Mounting Location (Continued) 5 Slide the locking knob into lock position on the back of the cradle. [. . . ] · For SUVs, minivans & 5-door vehicles, bring the cable into the car under the rubber molding for the tailgate, and continue under the interior trim. 6 From the trunk, route the cable around the passenger compartment and to the back of the cradle. CAUTION: · Do not pull the cable across sharp edges that could damage it. · Do not route the cable nearby areas where it could become tangled in driver's and passenger's feet. 10 7 Plug the antenna into the antenna into the back of the cradle--ANT. [. . . ]