User manual JVC LM-17G

[. . . ] ESPAÑOL ITALIANO LM-17G LM-15G INSTRUCTIONS FRANÇAIS DEUTSCH BEDIENUNGSANLEITUNG : LCD-VIDEO-MONITOR MANUEL D'INSTRUCTIONS : MONITEUR VIDEO LCD MANUALE DI ISTRUZIONI : MONITOR VIDEO LCD INSTRUCCIONES : MONITOR DE VIDEO LCD ENGLISH LCD VIDEO MONITOR INSTRUCTIONS LCD VIDEO MONITOR LM-17G LM-15G Thank you for purchasing this JVC LCD video monitor. Before using it, read and follow all instructions carefully to take full advantage of the monitor's capabilities. (* "LCD" stands for Liquid Crystal Display. ) For Customer Use: Enter below the Serial No. which is located on the rear of the cabinet. [. . . ] Recommended mode, 1024x768 at 60Hz for LM-15G and 1280x1024 at 60Hz for LM-17G . 7 ENGLISH Using the Menu This chapter contains information about how to changing monitor settings for your LCD Monitor. It is designed with an menu to help you easily adjust to its optimum performance. Note: In the PC mode, do the "AUTO SET UP" setting first, before adjusting any settings. For details, see "AUTO SET UP" on page 13. Summary of Control Buttons There are three control buttons located at the lower part of the front panel of your monitor: MENU/ENTER: Display and select a menu. You can also exit a menu by pressing this button repeatedly. UP(): Move upward through the choice in the submenu. If an adjustment bar is displayed, this button increases the setting value. Down() : Move downward through the choice in the submenu. If an adjustment bar is displayed, this button decreases the setting value. Menu Operation 1. For details, see the following "COLOR TEMP. " menu. LOW LIGHT ADJ. : At the video mode: You can adjust the brightness of the dark part of picture. At the PC mode: You can adjust the R. G. B. For details of the adjustments, see "HIGH LIGHT ADJ. " in page10 Next page: If you select `Next page' and press the `MENU/ENTER' button, the next menu will appear. 9 ENGLISH COLOR TEMP. Press the `UP' and `DOWN' button to choose the "COLOR TEMP. ", and then press the `MENU/ENTER' button to display the sub-menu. COLOR TEMP. HIGH NATURAL LOW USER 2. Press `UP' and `DOWN' button to choose one of four Color temp settings: HIGH, NATURAL, LOW and USER. "USER" setting: You can store the adjustments of "HIGH LIGHT ADJ. " to the "USER" setting. In "HIGH", "NATURAL" and "LOW", you cannot use "HIGH LIGHT ADJ. ". Press the `UP' or `DOWN' button to choose the "USER" , and then press the `MENU/ENTER' button to return to the "HIGH LIGHT ADJ. " menu. HIGH LIGHT ADJ. Next page RED GREEN BLUE 2. Press `UP' and `DOWN' button to choose "RED", and then press `MENU/ENTER' button to display the adjusting menu. RED 50 3. 4. Press `UP' or `DOWN' button to adjust the level, and then press `MENU/ENTER' button to return to the sub-menu Repeat step 3 and 4 for other colors "GREEN" and "BLUE" to complete the "HIGH LIGHT ADJ. " setting. 10 SYSTEM SETTING menu SYSTEM SETTING Exit SIGNAL LEVEL DISPLAY OSD POSITION COLOR SYSTEM AGC REMOTE All reset SIGNAL LEVEL: STD. : AMP. : You can choose the signal level from "STD. " or "AMP. ". Select this for normal operation. Select this to watch dark part of the picture better. If you select `DISPLAY' and press the `MENU/ENTER' button, you can confirm the current status; resolution, Horizontal frequency and Vertical frequency. DISPLAY: COLOR SYSTEM: You can choose the color system from NTSC, PAL, BW60 or BW50. Choose the correct color system when the color is abnormal or no color appears. [. . . ] Check that your graphic card outputs the analog RGB signal. The message "Signal Out of Range" appears on my monitor. This message appears when the input signal is beyond the monitor capability. Set your PC to a supported video mode; preferably 1024 x 768 at 60 Hz for LM-15G, 1280x1024 at 60Hz for LM-17G. [. . . ]