User manual JVC LT-32E478 Instruction Manual

[. . . ] LCD Flat Television Users Guide For Models: LT-42E488 LT-42E478 LT-37E488 LT-37E478 LT-32E488 LT-32E478 Illustration of LT-32E488 and RM-C1291 Important Note: In the spaces below, enter the model and serial number of your television (located at the rear of the television cabinet). Staple your sales receipt or invoice to the inside cover of this guide. Keep this user's guide in a convenient place for future reference. Keep the carton and original packaging for future use. Model Number: Serial Number: LCT2224-001B-A 0207TNH-II-IM Important Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: To reduce the risk of electric shock. [. . . ] Some programs may include additional text information which is usually found on text channel Text1. The other channels are available for future use. · Closed captioning may not work correctly if the signal being received is weak or if you are playing a video tape. · Most broadcasts containing closed captioning will display a notice at the start of the program. · To select the mode, press the C. C. See page 60. 37 Initial Setup Auto Shut Off This function automatically shuts off your TV when there is no signal from the channel the TV is on for 10 minutes. Press the MENU button Initial Setup Auto Shut Off Software Version Power Indicator Quick Start-up Low On On 2/2 ® ® To To To To "Initial Setup" enter "Auto Shut Off" turn "On" or "Off" Press the MENU button when finished Select Operate Back Exit · If the channel that you have on does not receive a signal for more than one minute, the blinking text "No Program or Weak Signal Auto shut off in 9 min. " appears on the screen, and starts the countdown. If no signal is being received within 10 minutes, the TV shuts itself off. BACK MENU Software Version You can confirm the Software Version. Press the MENU button Initial Setup 2/2 ® ® To "Initial Setup" To enter To "Software Version" To enter Press the OK button to close Press the MENU button when finished Auto Shut Off Software Version Power Indicator Quick Start-up On Low On Select Operate BACK Back MENU Exit Power Indicator Power indicator allows you to adjust the brightness of the power indicator Press the MENU button Initial Setup Previous 2/2 ® ® To To To To "Initial Setup" enter "Power Indicator" turn "High", "Low", "Off" Auto Shut Off Software Version Power Indicator Quick Start-up On Low On Press the MENU button when finished Select Operate BACK Back MENU Exit Notes : · When Off is selected : The LED disappears if you have a TV signal. The LED is lit as "Low" when there is no TV signal. · When the On Timer turns On, the LED is lit as "Low" when you turn the power off. · If you set a timer on the TV, the power indicator will light even if the TV is on stand by. 38 Initial Setup Quick Start-up Quick Start-up allows you to lessen the time for the TV to turn on and ready for viewing. Press the MENU button Initial Setup 2/2 ® ® To To To To "Initial Setup" enter "Quick Start-up" turn "On" or "Off" Auto Shut Off Software Version Power Indicator Quick Start-up On Low On Press the MENU button when finished Notes: · Standby power consumption is higher when you have this feature turned on. Select Operate BACK Back MENU Exit 39 Tuner Setup Auto Tuner Setup The auto tuner setup function is described on page 23 as the interactive plug-in menu. If you need to run the auto tuner setup again, follow the steps below. Press the MENU button ­ + Tuner Setup > Auto Tuner Setup ® ® ® ® To "Tuner Setup" Tuner Mode Scan Mode To enter To "Auto Tuner Setup" To enter To choose "Cable" or "Air" To "Scan Mode" Select To choose "Auto", "STD", "HRC" or "IRC" To "Start" Press the OK button (Programming will take serveral minutes) Air Auto Start Operate BACK Back MENU Exit The auto tuner is finished when the message "Programming Over !" appears onscreen. Notes: · When the Tuner Mode is set to "Cable", it is possible to select "Scan Mode" · If no channels were found using Auto Tuner Setup, check your antenna cable and the settings for Tuner Mode/Scan Mode. · You can also access the "Front Menu" screen by using the MENU button on the side of the TV instead of the remote control. It has "Video Status", "Aspect", "Auto Tuner Setup" and "Menu". Choose "Auto Tuner Setup" by pressing MENU on the side panel and enter by using the CHANNEL +/- buttons ( OPERATE ® ). 40 Tuner Setup Channel Summary Channel summary allows you to customize the line-up of channels received by your TV. You can add or delete channels from the line-up or prevent any unauthorized viewers from watching any or all channels. Press the MENU button To "Tuner Setup" ® To enter To "Channel Summary" ® To enter A channel having the Scan mark "" can be selected by using CH+/- (channel +/-) button. You can delete channels from the scan by removing the "". ® To the "Scan" column Press the OK button to include or delete from scan Press the MENU button when finished Note: · The number of a digital channel may change, depending on the time of some broadcastings. [. . . ] · There could be interference from another electrical appliance, such as a computer, another TV or VCR. Move any such appliances further away from the TV. · There could be interference from a high-wattage appliance, like a hairdryer or vacuum, operating nearby. Move the antenna away from the appliance or change to a coaxial cable connection which is less prone to interference. [. . . ]