User manual JVC MX-GT91R

[. . . ] COMPACT COMPONENT SYSTEM CA-MXGT91R CA-MXG71R CA-MXGT91R STANDBY/ON STANDBY PLAY & EXCHANGE CA-MXG71R STANDBY/ON STANDBY PLAY & EXCHANGE CD-R/RW PLAYBACK CD-R/RW PLAYBACK MX-GT91R MX-G71R INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. GVT0052-008A [B] Warnings, Cautions and Others IMPORTANT for the U. K. [. . . ] To protect your recording, remove these tabs. To re-record on a protected tape, cover the holes with adhesive tape. · If the tape direction is not correct, press TAPE 2 3 twice then 7 to change the tape direction. 5 Start playing the source -- FM, AM (MW/ LW), CD player, deck A, or auxiliary equipment connected to AUX jacks. · When the source is CD, you can also use CD Direct Recording (see page 21) and Auto Edit Recording (see page 22). · When the source is deck A, you can also use the dubbing method. (See "Dubbing Tapes" on page 21. ) To keep the best recording and playback sound quality If the heads, capstans, and pinch rollers of the cassette decks become dirty, the following will occur: · Impaired sound quality · Discontinuous sound · Fading · Incomplete erasure · Difficulty in recording To clean the heads, capstans, and pinch rollers Use a cotton swab moistened with alcohol. Pinch rollers Capstans 6 Start recording. On the unit: Press REC START/STOP. On the remote control: Press and hold REC START/STOP for more than 1 second. The (recording) indicator lights up on the display and recording starts. · If no cassette is inserted, "NO TAPE" appears on the display. If a protected tape is inserted, "NO REC" appears on the display. To remove the cassette, press EJECT 0 for deck B. Heads To demagnetize the heads Turn off the unit, and use a head demagnetizer (available at electronics and audio shops). ­ 20 ­ To record on both sides -- Reverse Mode Press REVERSE MODE so that the Reverse Mode indicator lights up like -- . · When using the Reverse Mode for recording, start recording in the forward (3) direction first. Otherwise, recording will stop when recording is done only on one side (reverse) of the tape. To cancel Reverse Mode, press the button again so that the Reverse Mode indicator lights up like -- . CD Direct Recording Everything on the CD goes onto the tape in the order it is on the CD, or according to the order you have made for Program play. On the unit ONLY: Dubbing Tapes You can record from one tape to another. 1 Put a recordable cassette into deck B. 3 Press one of the disc number buttons (CD1, CD2, and CD3) to select the disc, then 7. · If you want to make a program, perform steps 2 to 5 on page 17. After making a program, go to the next step. On the unit ONLY: 1 Press TAPE 2 3, then 7. 4 Press CD REC START. "CD REC" appears, and the (recording) indicator lights up on the display. Deck B starts recording and the CD player starts playing. When the recording is done, "CD REC FINISHED" appears on the display, and the CD player and deck B stop. 2 Put the source cassette in deck A, and a recordable cassette into deck B. · Put the cassettes in both decks so that the tapes will run in the forward (3) direction. 3 Press DUBBING. The (recording) indicator lights up on the display and dubbing starts. To stop dubbing, press 7 so that both decks (A and B) stop. To stop recording, press REC START/STOP or 7. So that a 4-second blank portion is created on the recording tape. (Remember a 4second blank is important when using Music Scan -- see page 19. ) To record on both sides -- Reverse Mode Press REVERSE MODE so that the Reverse Mode indicator lights up like -- . · When using the Reverse Mode for CD Direct Recording, start recording in the forward (3) direction first. When the tape reaches its end while recording a song in the forward direction (3), the last song will be re-recorded at the beginning of the reverse side (2). If you start recording on the reverse side (2), recording will stop when recording is done only on one side (reverse) of the tape. To cancel Reverse Mode, press the button again so that the Reverse Mode indicator lights up like -- . To record on both sides -- Reverse Mode Press REVERSE MODE so that the Reverse Mode indicator lights up like -- . [. . . ] For kraftigt indgangssignal vil resultere i unormal stoj og muligvis beskadigelse. I tilfælde hvor højttalerne udsættes for signalerne beskrevet nedenfor, kan der forekomme overbelastning og overbrænding af ledningerne i höjttalerne selv om signalstyrken er under den maksimale tilladte værdi. Husk derfor at at sænke højttalerlydstyrken i forvejen. 2) Signaler med høje niveauer der indeholder höjfrekvente komponenter dannet af en båndoptager der er indstillet til hurtig fremspoling. [. . . ]