User manual JVC RX-1010VTN parts list

[. . . ] Disconnect the mains plug to shut the power off completely. The POWER switch in any position does not disconnect the mains line. The power can be remote controlled. CAUTION To reduce the risk of electrical shocks, fire, etc. : 1. Do not remove screws, covers or cabinet. [. . . ] The 3D-PHONIC indicator goes off from the display. 24 English English Using the Surround Processor Using the DAP Modes You can use five DAP modes -- "Dance Club, Live Club, Hall, Pavilion, and Headphones. " These modes (except "Headphones") require the front speakers and the rear speakers, but do not require a center speaker to enlarge the sound field. Among the DAP modes, "Headphones" is very special. It can create the same stereo sound as you listen through the speakers off air while listening to a source using headphones. So, you can feel as if you were not using the headphones and listening to music in a room. On the front panel: 1. Press SURROUND so that the Control % / fi / @ / # buttons work for selecting the Surround Processor mode. Press Control % / fi until one of the DAP mode ("HEAD P, " "PAVILION, " "HALL, " "LIVE C" or "DANCE C") appears on the display. Each time you press the button, the Surround Processor modes change as follows: Ex. SURROUND Note: When one of the DAP modes is selected, the DAP indicator also lights up on the display. PROLOGIC OFF THEATER 3DACTION* 3CHLOGIC PAVILION* (One of the five modes appears) * As for the 3D-PHONIC modes (see page 23) and the DAP modes, one of the previously selected mode appears on the display. Press Control @ / # until the DAP mode you want appears on the display. Each time you press the button, the DAP modes change as follows: HEAD P DANCE C PAVILION LIVE C HALL Note: When changing the DAP modes to "PAVILION" or "HALL, " a reverberation sound comes out. This is because a long reverberation is applied to these two modes. HEAD Phones* PAVILION HALL LIVE Club DANCE Club Gives a spacious stereo effect when listening with headphones. Gives the spacious feeling of a pavilion with a high ceiling. · Pressing REAR (L) ­ decreases the output level up to ­10 dB. · Pressing REAR (L) + increases the output level up to +10 dB. Note: REAR (L) Once you have adjusted the DAP modes, the adjustment is memorized for each DAP mode. Continued to the next page. 26 English English Using the Surround Processor 4. Press EFFECT to select the effect level. Each time you press the button, the effect level changes as follows: EFFECT 1 EFFECT 2 EFFECT 3 EFFECT 4 EFFECT 4 EFFECT 5 To cancel the DAP mode Select "OFF" in step 2. The DAP indicator goes off from the display. 27 With this receiver, you can use two types of the surround modes -- Dolby Surround and JVC Theater Surround. Speaker Arrangements for Surround Modes The following illustrations show how to obtain the optimum sound environment for various surround mode settings. Try to find the speaker direction and location to create the optimum sound field. CASE 1 When you have added a center speaker and rear speakers Front speaker TV Center speaker Front speaker Rear speaker Rear speaker In this case: 1. Select "PROLOGIC" or "THEATER. " 2. Select "NORMAL" or "WIDE" for center mode. See pages 29 to 32 for more details. CASE 2 When you have added rear speakers (without a center speaker) Front speaker TV Front speaker Rear speaker Rear speaker In this case: 1. Select "PROLOGIC" or "THEATER. " 2. Select "PHANTOM" for center mode. See pages 29 to 32 for more details. CASE 3 When you have added a center speaker (without rear speakers) Front speaker TV Center speaker Front speaker In this case: 1. Select "NORMAL" or "WIDE" for center mode. See pages 29 to 32 for more details. 28 English English Using the Surround Processor Preparing for Surround Modes Once you have set the surround modes, you can use the same adjustments every time you want to activate the surround mode you want. [. . . ] VCR, DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p/75 ohms Video Output Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCR, MONITOR OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p (at 1 Vp-p input), sync negative Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]