User manual JVC RX-5022RSL

[. . . ] DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. If nonetheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. [. . . ] Each time you press the button, the display changes as follows: OFF MAX MID CONTROL DOWN UP OFF : Select this when you want to enjoy surround with its full dynamic range. (No effect applied. ) MID : Select this when you want to reduce the dynamic range a little. MAX : Select this when you want to apply the compression effect fully. (Useful at night. ) 14 EN08-20. RX-5022RSL[B]_f 14 02. 1. 16, 5:33 PM Sound Adjustments Front Panel Display TEST Remote Control A/V CONTROL RECEIVER CENTER STANDBY/ON AUDIO 1 EFFECT 2 5 8 0 SOUND 3 REAR L TV 4 MENU 6 REAR R VCR RX-5022R AUDIO/VIDEO CONTROL RECEIVER FM/AM TUNING UP STANDBY FM/AM PRESET UP FM MODE DIMMER PTY SEARCH TA/NEWS/INFO DISPLAY MODE SUBWOOFER +/?SOUND 7/P ENTER 9 DVD SUBWOOFER 10 RETURN 10 SLEEP TA/NEWS/INFO 100 MEMORY DOWN DOWN ANALOG DIGITAL AUTO LINEAR PCM DIGITAL SPK L C R S. WFR LFE LS S RS TUNED STEREO PRO LOGIC ??DSP H. PHONE INPUT ATT AUTO MUTING SLEEP RDS TA NEWS INFO VOLUME MASTER VOLUME PTY?PTY SEARCH?PTY REW REC PAUSE DISPLAY MODE FF CD?DISC STANDBY/ON CH- DVD SURROUND ON/OFF INPUT ANALOG INPUT DIGITAL VCR TV SOUND ADJUST SETTING TAPE/CDR CD DVD ANALOG /DIGITAL FM/AM INPUT ATT TV SOUND VCR CD SURROUND MODE SPEAKERS ON/OFF TAPE/CDR FM/AM CONTROL DOWN UP FM MODE ON/OFF DIMMER TV/VIDEO SURROUND MODE MUTING SOURCE NAME PHONES VCR CH TV CH TV VOLUME VOLUME REMOTE CONTROL RM - SRX5022R INPUT ATT ADJUST CONTROL UP 5/DOWN ? Once each of following settings has been adjusted, this receiver memorizes the adjustment for each source. 1 Attenuating the Input Signal Remote NOT Press ADJUST repeatedly until ?BASS?(with the current setting)* appears on the display. ADJUST SETTIN When the input level of the analog source is too high, the sounds will be distorted. If this happens, you need to attenuate the input signal level to prevent the sound distortion. * ?0?If you have already changed the setting, another number (level) will be shown. BASS : To adjust the bass (?10 to +10). TREBLE : To adjust the treble (?10 to +10). 1 Press and hold INPUT ATT (INPUT ANALOG) so that the INPUT ATT indicator lights up on the display. INPUT ANALOG INPUT ATT 2 Press CONTROL UP 5/DOWN ?to adjust the bass or treble sounds level. ?Each time you press the button, the sound level changes by 2 steps. CONTROL DOWN UP ?Each time you press the button, the band alternates between FM and AM (MW/LW). ANALOG SPK L C R S. WFR LFE LS S RS 1 Tune in the station you want to preset (see ?Tuning in Stations Manually?). ?If you want to store the FM reception mode for this station, select the FM reception mode you want. on page 17. ANALOG SPK L C R S. WFR LFE LS S RS TUNED STEREO AUTO MUTING VOLUME CH- Ex. : When the FM band is selected. TUNED STEREO AUTO MUTING VOLUME CH- 2 Press FM/AM TUNING UP/ DOWN until you find the frequency you want. ?Pressing FM/AM TUNING UP increases the frequency. Pressing FM/AM TUNING DOWN decreases the frequency. UP Remote NOT FM/AM TUNING 2 Press MEMORY. ?CH-?appears and the channel number position starts flashing on the display for about 5 seconds. ANALOG SPK L C R S. WFR LFE LS S RS MEMORY DOWN TUNED STEREO AUTO MUTING VOLUME Notes: ?When you press and hold FM/AM TUNING UP/DOWN for a few seconds in step 2, the frequency keeps changing until a station is tuned in. When a station of sufficient signal strength is tuned in, the TUNED indicator lights up on the display. When an FM stereo program is received, the STEREO indicator also lights up. CH- 3 Press FM/AM PRESET UP/ DOWN to select a channel number while the channel number position is flashing. ANALOG SPK L C R S. WFR LFE LS S RS FM/AM PRESET UP DOWN TUNED STEREO AUTO MUTING VOLUME CH- 16 EN08-20. RX-5022RSL[B]_f 16 02. 1. 17, 9:08 AM Tuner Operations 4 Press MEMORY again while the selected channel number is flashing on the display. MEMORY Selecting the FM Reception Mode When an FM stereo broadcast is hard to receive or noisy, you can change the FM reception mode while receiving an FM broadcast. You can store the FM reception mode for each preset station (see page 16). The selected channel number stops flashing. The station is assigned to the selected channel number. ANALOG SPK L C R S. WFR LFE LS S RS TUNED STEREO AUTO MUTING VOLUME CH- 1 While listening to an FM station, press FM MODE. ? [. . . ] does not disappear, unplug the AC power cord, then plug it back again. If speaker wiring is not short-circuited, contact your dealer. on the front panel to Press STANDBY/ON turn off the receiver. After unplugging the power cord, consult your dealer. [. . . ]