User manual JVC RX-5060 Instruction Manual

[. . . ] AUDIO/VIDEO CONTROL RECEIVER RX-5060B TA/NEWS/INFO DISPLAY MODE INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. LVT1507-001A [J] Warnings, Cautions and Others/ Mises en garde, prcautions et indications diverses CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN For U. S. A This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. [. . . ] The signals below the preset frequency level will be sent to and be reproduced by the subwoofer (or by "LARGE" speakers when "SUBWOOFER" is set to "SUBWOOFER NO"). Select one of the crossover frequency levels according to the size of the small speaker connected. CROSS 80HZ: Select when the cone speaker unit built in the speaker is about 12 cm. Selecting the Main or Sub Channel You can select the playback sound (channel) you want while playing digital software recorded (or broadcast) in Dual Mono mode (see page 24), which includes two monaural channels separately. Dual Mono--DUAL MONO Select the playback sounds (channel). MONO MAIN: Select to play back the main channel (Ch 1). * Signal indicator "L" lights up while playing back this channel. MONO SUB: Select to play back the sub-channel (Ch 2). * Signal indicator "R" lights up while playing back this channel. CROSS 100HZ: Select when the cone speaker unit built in the speaker is about 10 cm. CROSS 120HZ: Select when the cone speaker unit built in the speaker is about 8 cm. CROSS 150HZ: Select when the cone speaker unit built in the speaker is about 6 cm. CROSS 200HZ: Select when the cone speaker unit built in the speaker is about 5 cm. MONO ALL: Select to play back both the main and subchannels (Ch 1/Ch 2). * Signal indicators "L" and "R" light up while playing back these channels. Notes: Notes: If you have selected "LARGE" for all activated speakers (see page 18), this function is fixed to "CROSS OFF. " Crossover frequency is not valid for "HEADPHONE" and "3D H PHONE. " The Dual Mono format is not identical with bilingual broadcasting or the MTS (Multichannel Television Sound) format used for TV programs. So this setting does not take effect while watching bilingual or MTS programs. * Dual Mono signals can be heard from the following speakers--L (left front speaker), R (right front speaker), and C (center speaker)--with respect to the current Surround setting. With Surround Activated Dual Mono Setting MAIN SUB ALL Without Surround L Ch 1 Ch 2 Ch 1 R Ch 1 Ch 2 Ch 2 L -- -- Center speaker setting SMALL/LARGE NONE Low frequency effect attenuator--LFE ATTENUATE If the bass sound is distorted while playing back software encoded with Dolby Digital or DTS, set the LFE level to eliminate distortion. This function takes effect only when the LFE signals come in. Select one of the following: LFE ATT 0dB: Normally select this. C Ch 1 Ch 2 R -- -- L Ch 1 Ch 2 R Ch 1 Ch 2 -- Ch 1+Ch 2 -- Ch 1+Ch 2 Ch 1+Ch 2 LFE ATT -10dB: Select when the bass sound is distorted. Midnight mode--MIDNIGHT MODE You can enjoy a powerful sound at night using Midnight Mode. Select one of the following: MIDNIGHT 1: MIDNIGHT 2: Select when you want to reduce the dynamic range a little. Select when you want to apply the compress effect fully (useful at midnight). MIDNIGHT OFF: Select when you want to enjoy playback with its full dynamic range (no effect applied). 19 English Basic Settings English Setting for Effective Surround Operations Virtual Surround Back--VIRTUAL SBACK You can enjoy the surround back channel while playing back Dolby Digital Surround EX software or DTS-ES software without the surround back speakers. This function creates the great surround effect from the behind as if you have connected the surround back speakers. Select "VRTL SB ON" to activate Virtual Surround Back. VRTL SB ON: While you play Dolby Digital Surround EX software or DTS-ES software, the VIRTUAL SB (Surround Back) indicator lights up. VRTL SB OFF: Select to deactivate Virtual Surround Back. Setting the Digital Input Terminals When you use the digital input terminals, register which components you have connected to the digital input terminals. Digital Input terminal--DIGITAL IN Set the components connected to the digital terminals. As you rotate MULTI JOG, the digital input terminals are set to used for the following digital components: " 1DVD 2TV 2TV 2CD " 1DVD 2CDR " " 1CD 2CDR " " 1TV 2CDR " " " 1CDR 2TV 1DVD 2CD 1CD 1TV 2DVD " 1CD 2DVD " 1TV 1CDR 2DVD " 1CDR 2CD (back to the beginning) Notes: When you have set "NONE" for "SURR SPEAKERS, " this function is not available. [. . . ] Check with your dealer to be sure you have the correct antenna. (See pages 4 and 5. ) Move the antenna farther from automobile traffic. Press STANDBY/ON on the front panel to turn off the receiver. Turn on the receiver again, and adjust the volume. [. . . ]