User manual JVC RX-ES9SL

[. . . ] HOME CINEMA CONTROL CENTER RX-ES9SL INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. LVT1112-001A [B] Warnings, Cautions, and Others IMPORTANT for the U. K. [. . . ] There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again. 1 Press SETTING. MULTI JOG now works for the setting operation. 2 Turn MULTI JOG until the setting item you want to set appears on the display, then press SET. As you turn MULTI JOG, the indication changes as follows: ANALOG L SUBWFR VOL R SUBWFR CNTR SP FRNT SP CNTR DL SURR SP SURR DL LFE CROSS D. COMP DIGITAL IN* AUTO SR MODE (Back to the beginning) QUICK SETUP * Setting item you can select appears on the display after "DIGITAL IN" appears for a few seconds. 3 Turn MULTI JOG to select the appropriate setting for the item selected in step 2, then press SET. Your setting is stored. ANALOG L SUBWFR VOL R Ex. : When selecting "1VR2STB3DVD" for "DIGITAL IN. " 19 15-20_RX-ES9SL[B]f 19 03. 6. 27, 16:49 Basic settings Setting Auto Surround--AUTO SR You can enjoy Surround mode simply by selecting the source (with digital input selected for that source). Select "ON" when activating Auto Surround. ON: If multi-channel signal comes in, an appropriate Surround mode will be turned on. If Dolby Digital 2 channel or DTS 2 channel signal including surround signal comes in, "PLII MOVIE" will be selected. If Dolby Digital 2 channel or DTS 2 channel signal not including surround signal comes in, "STEREO" will be selected. If Linear PCM signal comes in, nothing will change. The AUTO SR indicator lights up on the display. OFF*: Select this to deactivate Auto Surround. Setting the Auto Function mode--MODE The video components can be operated through this receiver by activating Auto Function mode. This function takes effect for the following sources--DVD (except DVD MULTI), STB, and VR, when they are connected using SCART cables. AUTO1: When a video component is turned on while the receiver is on, the receiver selects the video component as the source automatically. The AUTO MODE indicator lights up on the display. When a video component is turned on while the receiver is on or TV Direct activates, the receiver selects the video component as the source automatically. When a video component is turned on while the receiver is off, TV Direct activates and the receiver selects the video component as the source automatically. When a video component currently selected as the source is turned off while the receiver is on or TV Direct activates, the receiver changes the source to the previously selected one. When all video components are turned off while the receiver is on or TV Direct activates, the receiver is turned off automatically. The AUTO MODE indicator lights up on the display. MANUAL*: Select the source manually. AUTO2: * Initial setting NOTES This function does not take effect in the following cases: While playing an analogue source, and While selecting "DGTL D. D. " or "DGTL DTS" as the fixed digital input mode (see page 12). If Surround mode is automatically activated by Auto Surround, any other Surround mode in use will be canceled temporarily. When the multi-channel digital signal stops coming in, "PLII MOVIE" activates. If you press SURROUND with Auto Surround activated, Auto Surround will be canceled temporarily for the currently selected source. Auto Surround setting will be restored in the following cases: When you turn the receiver off and on, When you change the source, When you change the analogue/digital input, and When you reset "AUTO SR" to "ON" again. * Initial setting NOTE When selecting VR as the source, "AUTO1" or "AUTO2" may not work if you only turn on the VR. [. . . ] If speaker wiring is not short-circuited, contact your dealer. Consult your dealer after unplugging the power cord. The unit is overloaded because of a high voltage. Remote control does not operate as you intend. The remote control is not ready for your intended operation. Press a source selecting button or TONE first, then press the buttons you want to use. [. . . ]