User manual JVC WB-1540U

[. . . ] OUTDOOR HOUSING WB-1540 WB-1550 INSTRUCTIONS ESPAÑOL This instruction book is made from 100% recycle paper. LST0267-001A For Customer Use: Enter below the Serial No. Retain this information for future reference. WB-1540/WB-1550 ITALIANO FRANÇAIS DEUTSCH ENGLISH These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances. IMPORTANT SAFEGUARDS 1. All warnings on the product and in the operating instructions should be adhered to. [. . . ] If it falls, it may cause injury or accidents. Regularly check for the deterioration of attaching parts and the loosening of the screws caused by vibrations. If it falls, it may cause injury or accidents. Do not install in locations where radiation, X-rays, or corrosive gases are emitted. Doing so may cause the camera to malfunction. Keep all packaging out of the reach of children. If used for play, it may cause injury or suffocation. 4 System Example VN-C625 and VN-C655 Systems WB-1540 / WB-1550 Power Cable (DC 12V) Not in use on this system. (T1) Power Cable (AC 24V) AC 24 V Power Supply T1 Coaxial Cable Monitor WB-1540 / WB-1550 (Main Board) TB1 AC24V ~ INPUT LED1 Alarm Cable Alarm Device LAN Cable To TB1 (Connected) LAN TO CAMERA Power Indicator Red light turns on during power supply. PC VN-C625/655 Supplied Converter Unit To [POWER INPUT DC 18 V] Terminal (VN-C655) To [POWER INPUT DC 12 V] Terminal (VN-C625) Fuse T To [VIDEO OUT] Terminal To [ALARM IN/OUT] Terminal To [10 BASE-T/100 BASE-TX] Terminal Ceiling Mount of Network Camera CAUTION: T1: Not in use on this system. Ensure to bind both ends of cables that are not in use with insulating tape. T2: Power will not be supplied to this unit and the installed camera when the fuse on the main board burns out. When this occurs, please consult your nearby JVC dealer as exchange of fuse according to the rating (125 V - 5 A) will be required. TK-C625, TK-C655 and TK-C676 Systems WB-1540 / WB-1550 Power Cable (DC 12 V) Not in use on this system. (T1) LAN Cable Power Cable (AC 24 V) To Insulated AC 24 V Power Supply T1 Coaxial Cable Communication Cable VIDEO INPUT TO CAMERA REMOTE CONTROL UNIT RM-P2580 SETUP MENU SET POWER ALARM KEY LOCK CAMERA POSITION AUTO F-1 F-2 F-3 WB-1540 / WB-1550 (Main Board) CLOSE LENS SPEED CAMERA/POSITION PAN/TILT POSITION 1 OPEN 2 5 8 /HOME 3 6 9 ENTER CAMERA IRIS FOCUS AF TB1 AC24V ~ INPUT LED1 4 7 CLEAR OPTION 1 OPTION 2 NEAR FAR AUTO PAN AUTO PATROL WIDE ZOOM TELE 0 To TB1 (Connected) RM-P2580 TO CAMERA Power Indicator Red light turns on during power supply. Fuse T To [VIDEO OUT/TO CCU] Terminal To [POWER INPUT To [CONTROL/ALARM IN, OUT] Terminal AC 24 V ~] Terminal Ceiling Mount of Combination Camera CAUTION: Ensure to turn of the power of devices in use before connecting. Refer to the instruction manual for the combination camera that is supplied with this unit as well during connection and installation. Ensure to bind both ends of cables that are not in use with insulating tape. T2: Power will not be supplied to this unit and the installed camera when the fuse on the main board burns out. When this occurs, please consult your nearby JVC dealer as exchange of fuse according to the rating (125 V - 5 A) will be required. 5 Installation and Connection (WB-1540) Disassembling the Housing 1. Main Housing Unit Dismantle the gasket and gasket gland Loosen the 6 Screws B (M4) using a driver, followed by dismantling the gasket and gasket gland from the lower housing. T The 6 Screws B (M4) cannot be totally removed from the gasket to prevent it from falling off. 2. Dismantle the lower housing Loosen the 3 Screws A (M4 x 6) using a driver, followed by dismantling the lower housing from the main housing unit. T The lower housing is connected to the main housing unit using a safety wire. 2. Screw A (M4 x 6) x 3 Lower Housing Safety Wire Gasket 1. Gasket Gland CAUTION: Pay careful attention to store the dismantled parts and screws until assembly is complete to prevent them from being misplaced. Screw B (M4) x 6 TK-C625 Mounting the Camera (TK-C625) Interior of Housing JVC Mark Notch Before mounting. Remove the ceiling mount cover of the camera and guide the cables supplied with WB-1540 through the cover. T For further details, please refer to the instruction manual of the camera in use. 1. Camera Mounting Bracket Connect the AC 24 V output cable to the camera Connect the AC 24 V output cable of the main board to the camera's ceiling mount bracket. 2. Connect other cables Connect the necessary cables supplied with the housing (coaxial video cable, communication cable, etc. ) to the ceiling mount. Safety Wire Main Board 2. 1. AC 24 V Output Cable Cables Cover FRONT Mark CAUTION: Connect the communication cable to the [ALARM IN/OUT] and [CONTROL] terminals if necessary. For safety reasons, ensure to cut off any excess cable and bind using an insulating tape before use. [. . . ] Pay attention when handling the desiccant in order to maintain its effectiveness. · Do not remove it from the bag until you are about to use it. · Do not wet it or touch it with wet hands. · Assemble promptly upon adhering the desiccant. [. . . ]