User manual JVC XM-R700

[. . . ] PORTABLE MINIDISC RECORDER TRAGBARER MINIDISC-RECORDER ENREGISTREUR DE MINIDISC PORTABLE DRAAGBARE MINIDISC-RECORDER XM-R700SL INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS GEBRUIKSAANWIJZING For Customer Use: Enter below the Model No. is located on the bottom of the cabinet and Serial No. Retain this information for future reference. Serial No. LVT0621-001A [E] WICHTIGER HINWEIS FÜR LASER-PRODUKTE / IMPORTANT POUR LES PRODUITS LASER /BELANGRIJKE INFORMATIE VOOR LASERPRODUKTEN ACHTUNG! [. . . ] It must be set to the close position before recording or editing. Accidental erasure prevention knob · Remote control operation will be disabled during recording or editing. · Unplugging or plugging of the connection cord or microphone should be avoided during recording. Open Close · Removal of the rechargeable battery should be avoided For recording For protecting during recording. Otherwise, you cannot open the lid unor editing erasure less the rechargeable battery is reinserted or AC adaptor is connected to the unit. 8 English Check Items Before Starting Recording English · The MD is not the Play-only type one. · The accidental erasure prevention knob of the MD cartridge is set to the close position. · The MD has enough space for recording. If not, carry out ALL ERASE or ERASE function mentioned later to erase all the tracks or desired tracks in the MD. You can check the recordable remaining time of the MD by repeatedly pressing the DISPLAY/CHARA. (See "Showing the Disc Information" on page 7. ) Standard Recording CAUTIONS: · Be sure that the rechargeable battery is fully charged. Otherwise, the unit may shut off, leaving recording unfinished. · While "UTOC Writing" appears on the display, to avoid improper recording, do not give a shock to the Unit and do not disconnect any cable from the Unit, including the AC adaptor's cable. Notes · The recording operation is possible only with the buttons on the unit. · When a stereo signal is recorded in MONO mode, stereo sound will be heard though the signal is correctly recorded in MONO mode. 1 2 3 Check the things before recording. See "Check Items Before Starting Recording" above. Insert an MD with its label side facing up. Proceed to the next step after "TOC Reading" goes out on the display. Slide the REC switch. The unit enters Rec/Standby mode, the REC indicator lights up, and the disc mark blinks. The track number is increased by one. (Appears only if MONO is selected. ) Total track number Remaining time Recording mode · To cancel Rec/Standby mode, press the 7/CHARGE button. 4 Within two minutes, press the REC MODE button to select the recording mode. Each time you press the button, the display changes as follows: SP = LP2 = LP4 = MONO SP: Signifies standard-hour stereo recording. The number of hours usable for recording is the same shown on the package of the MD. LP2: Signifies 2 times long-hour stereo recording. The number of hours usable for recording is twice long as shown on the package of the MD. LP4: Signifies 4 times long-hour stereo recording. The number of hours usable for recording is 4 times long as shown on the package of the MD. MONO: Signifies standard-hour monaural recording. The number of hours usable for recording is twice long as shown on the package of the MD. as as as as 5 6 7 Play the recording source. Adjust the recording level for analog input only. See "Adjusting the recording level" on page 10. Press the 6 button to start recording. When the MD becomes full, "UTOC Writing" appears on the display, indicating that the recording is successfully completed. [. . . ] Handling the MDs · Do not open the shutter. The shutter is usually locked to prevent opening. Do not force to open it or the disc may be destroyed. 18 English Troubleshooting Guide English Before requesting service for this unit, check the chart below for a possible cause of the problem you are experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation. [. . . ]