User manual KAWAI SX-210

[. . . ] 13 6. 2 Quit " SETUP " menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6. 3 Rinsing temperature setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6. 4 Washing temperature setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6. 5 Rinse aid dispensing setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 14 CW 620/630 Rinse aid pump total operating minutes display. This value can be reset after pump maintenance see below. Detergent pump total operating minutes display. This value can be reset after pump maintenance see below. Energy consumption (kW) display The Pc option indicates the total kW consumed since installation of the dishwasher or since the latest reset. Display of the number of cycles performed When scrolling through the appliance parameters, the "tc 88888" item will also appear; this is the count of the total cycles performed by the dishwasher since installation. This parameter cannot be modified or reset unless the software is reprogrammed. Customisation of duration of program P4. 15 CW 620/630 Steam extraction system operating time display and setting This submenu and the relative functions can only be accessed with the aid of a password available on SmegTech and only by technical staff. 6. 2 Quit " SETUP " menu Wait more than 10 seconds without pressing any button and the appliance quits this menu automatically, or press the on/off button to exit. Caution: the tank and boiler temperatures shown on the display may be different from the actual temperatures by a few degrees, especially in transient phases (just after the FILL is completed, just after the end of the cycle, etc. ) due to the inertia of the measurement probe. The duration of program P4 can be customised from 3 to 10 minutes Access the programming procedure and scroll through to "inF" using the press the minutes) button, then scroll through to 03:00 and button to set the time required (from 3 to 10 After a few seconds without the user pressing any buttons, the display will return to the normal operating status and the modifications will be saved. 6. 14 Steam extraction time setting (optional if installed) Steam extraction system operating time display and setting 20 CW 620/630 6. 15 Service setting (for AfterSales Service only) See information on Smegtech 6. 16 Starting the peristaltic pumps ­ rapid filling of detergent and rinse aid delivery circuit. Perform after the parameter modification procedure explained in the previous point. With the dishwasher powered up, access "programming mode" by pressing the on/off button for a few seconds; at the "beep", release the button and press it again quickly within 0. 5 seconds. The peristaltic pumps continue to operate until the same button is pressed again. The rinse aid and detergent symbol lights remain on as long as the pumps are on; bear in mind that the rinse aid peristaltic pump fills the circuit in about 7 minutes, while for the detergent it only takes 2 minutes. 21 CW 620/630 7 MALFUNCTIONS SHOWN ON THE DISPLAY (FOR THE TECHNICIAN) The dishwasher is able to identify a number of malfunctions and show them on the display. If the problem persists after the dishwasher has been switched off and back on, proceed as described below: The antiflooding system has been Err01 activated (for the relevant models only). Err04 Tank temperature probe malfunction Large water leak: check the origin of the problem. Tank temperature probe disconnected or not working. The tank does not fill within the allowed time: check water intake tap, dynamic pressure in intake system, cleaning of water intake filter, possible damage to water intake hose or cleaning of rinsing nozzles. [. . . ] Rinsing temperature too low DISHES NOT PROPERLY DRIED Check container of rinse aid and whether it is suitable for the type Rinse aid unsuitable or not of mains water. Restore T Stop ON being delivered correctly. and/or connect the appliance to a Water hardness above 12°f or hot water supply. large amounts of dissolved salts If the problem persists, contact the aftersales service. [. . . ]