User manual KB ELECTRONICS KBPB

[. . . ] KBPB & KBCC-R SUPPLEMENTAL INFORMATION DESCRIPTION The Anti-Plug Reversing Module used in the KBPB and KBCC-R models has been changed from APRM-2C to APRM-3. The General Performance Specifications of these products have not changed. [. . . ] Fire and/or electrocution can result due to improper use of this product. Power Main Speed Potentiometer Forward-Brake-Reverse Switch TB1 P1 P2 P3 S1 S2 S3 S4 + ARMATURE P1 P2 P3 S1 S2 S3 S4 A1 TB1 FWD-BRK-REV SWITCH REV BRK FWD HIGH WIPER LOW MAIN SPEED POTENTIOMETER Forward-Brake-Reverse and Run-Brake-Jog Switches with Main Speed Potentiometer P1 P2 P3 S1 S2 S3 S4 TB1 FWD-BRK-REV SWITCH REV BRK FWD HIGH WIPER LOW MAIN SPEED POTENTIOMETER JOG BRK RUN RUN-BRK-JOG SWITCH FWD BRK REV FWD-BRK-REV SWITCH L2 A2 AC LINE INPUT L1 CHASSIS TB3 GROUND (EARTH) Run-Brake and Forward-Reverse Switches Forward-Brake-Reverse Switch with Adjustable Forward and Preset Reverse Speed TB1 P1 P2 P3 S1 S2 S3 S4 FWD-REV SWITCH REV RUN-BRAKE SWITCH FWD P1 P2 P3 S1 S2 S3 S4 TB1 HIGH WIPER LOW MAIN SPEED POTENTIOMETER Forward-Brake-Reverse and Run-Brake-Jog Switches with Main Speed Potentiometer and Remote Jog Potentiometer TB1 Tach-Generator Feedback Connections 50 Volts per 1000 RPM Tach-Generator 7 Volts per 1000 RPM Tach-Generator P1 P2 P3 S1 S2 S3 S4 FWD-BRK-REV SWITCH REV RUN-BRK-JOG SWITCH BRK FWD RUN HIGH WIPER LOW MAIN SPEED POTENTIOMETER BRK JOG "B" TERMINAL (ON KBMM) "T" TERMINAL (ON KBMM) TB2 F+ F- TB2 F+ F- + TACH-GENERATOR + TACH-GENERATOR REMOTE JOG POTENTIOMETER KB ELECTRONICS, INC. 12095 NW 39th Street, Coral Springs, FL 33065-2516 · (954) 346-4900 · FAX (954) 346-3377 Outside Florida Call Toll Free (800) 221-6570 · info@kbelectronics. com www. kbelectronics. com (A40150) ­ Rev. C ­ 7/2006 Print Code KBPB & KBCC-R SUPPLEMENTAL INFORMATION The latest versions (11/2000) of the KBPB and KBCC-R controls do not contain Inhibit terminals on the terminal block. The Inhibit feature is available, however, by wiring a switch or contact to the I1 and I2 QD terminals on the PC board. The control uses the S2 terminal for brake-to-stop operation (open to stop, close to run). If the application requires coast-to-stop operation, connect the Inhibit Switch as shown below. I2 P1 P3 P2 I1 T B F+ A+ L2 L1 Do not route the Inhibit wires with AC line or motor wires unless shielded cables are used. One side of the Inhibit Switch connects to the new piggyback I1 QD Terminal. The other side of the Inhibit Switch connects to the I2 QD Terminal (or the Fterminal on Terminal Block TB2). It is recommended that the Inhibit Switch wires be routed (and secured with wire ties) with other signal wires (S1, S2, S3, etc. ). AInhibit Switch (Close to Coast-to-Stop) (Open to Run) F- MOUNTING INSTRUCTION FOR CHASSIS & IP-20 CONTROLS Note: KBPB shown. The KBCC-R uses the same PC board. SAFETY WARNING! This drive contains electronic Start/Stop circuits which can be used to start and stop the drive. However, these circuits are never to be used as safety disconnects since they are not fail-safe. Be sure to follow all instructions carefully. Fire and/or electrocution can result due to improper use of this product. WARNING!This control must be mounted in an enclosure. [. . . ] You must read the Safety Warning which accompanies this product. KB ELECTRONICS, INC. (A40150) ­ Rev. C ­ 7/2006 Print Code 12095 NW 39th Street, Coral Springs, FL 33065-2516 · (954) 346-4900 · FAX (954) 346-3377 Outside Florida Call Toll Free (800) 221-6570 · info@kbelectronics. com www. kbelectronics. com [. . . ]