User manual KENMORE 625.383060

[. . . ] OWNER'S MANUAL Water Softeners With Deluxe Valve MODEL NOS. 300 Series 625. 383060 300 Series 625. 393060 Caution: Read and follow all safety rules and operating instructions before first use of this product. Questions ?Visit www. KenmoreWater. com or call toll free 1-800-426-9345 (M - F, 7AM - 8 PM CST) Repair or Parts ?Call toll free 1-800-366-7278 See back cover for other Sears service numbers. [. . . ] That is equivalent to eating 2-1/2 slices of white bread. WATER SOFTENING SALT WITH IRON REMOVING ADDITIVES Some salts have an additive to help the softener handle iron in the water supply. These salts may be used if your water supply has a high iron content. It is recommended to use Sears Resin Bed Cleaner (refer to the Parts List in back of manual for part number) for periodic treatments to keep your resin bed clean. This is available at your local Sears store. Persons who are concerned about their drinking water should consider a Kenmore Drinking Water System that will remove or reduce in excess of 90% of the sodium and other drinking water contaminants. + 25 % = Questions?Call The Kenmore Water Line 1-800-426-9345 21 Check List CHECK LIST OF STEP-BY-STEP GUIDES TO INSTALL Review the following list to ensure you have completed all the installation procedures. Remove cardboard packaging from salt tank. Bypass Valve(s) Water Supply Valve Inlet ____3. Is the incoming water going to the valve inlet? Plastic ____4. Is the bypass valve placed into the service position?Are the drain lines clamped and secured?Is the unit plugged into a continuously live outlet?See page 20. FOR SERVICE Close bypass valve. Outlet Valve Note: Stem may be installed in either direction. The end with writing should be pulled out for service position. Bypass Valve Inlet Valve 3-Valve FIG. 30 22 Faceplate Timer Features EXTRA RECHARGE Sometimes, a manually started regeneration (recharge) may be desired, or needed. Two examples are: · You have used more water than usual (guests visiting) and you may run out of soft water before the next timer started regeneration. · You did not refill the softener with salt before it was gone. Add salt to the softener before regenerating. You can start a regeneration right away, or you can set the timer to regenerate at the next 2:00 AM (or other preset recharge time). RECHARGE NOW Press the REGENERATION button and hold for 3 seconds. The words RECHARGE NOW begin to flash in the display, and the softener enters the fill cycle of regeneration right away. This regeneration will last for about 2 hours. [. . . ] 625. 383060 and 625. 393060 4 3 2 1 5 28 6 27 26 7 Rating Decal Location 25 24 23 22 21 8 9 10 11 12 20 19 17 13 16 18 15 14 Questions?Call The Kenmore Water Line 1-800-426-9345 42 Parts List Kenmore MODEL Nos. 1 1 2 3 -- 4 5 6 -- 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Part Number ------7284095 7284134 7284142 7275907 7288544 7284582 7284566 7284621 7219888 7082150 7003847 7100819 7137913 7287140 7284613 0900431 1103200 9003500 7239155 7105047 0502272 7287166 7170270 7077870 7170254 7170296 7141001 7176292 7088033 3442699 7287205 7282580 Part Description Cover Lock (Required for shipping only) Rim Insert (Required for shipping only) Cover (main) Salt Hole Cover (order following decal) Instruction Decal Transformer, 24V-10VA Timer Repl. (PWA) Faceplate (order following decal) Faceplate Decal Rim Brinewell Cover Wing Nut, 1/4" O-Ring Brinewell Decal, Salt Level Salt Storage Drum Plastic Screw, 1/4" x 5/8" Tube Clamp Tube Adaptor Grommet Brine Valve Assembly (also see pages 44 & 45) Replacement Distributor Resin Resin Tank (including Key No. [. . . ]