User manual KENMORE 625.383560

[. . . ] OWNER'S MANUAL Water Softeners With Deluxe Valve MODEL NOS. IntelliSoft 350 Series 625. 383560 IntelliSoft 350 Series 625. 393560 Caution: Read and follow all safety rules and operating instructions before first use of this product. Questions ?Visit www. KenmoreWater. com or call toll free 1-800-426-9345 (M - F, 7AM - 8 PM CST) Repair or Parts ?Call toll free 1-800-366-7278 See back cover for other Sears service numbers. [. . . ] If you wish to turn the salt monitor off, press the SIGNAL LIGHT ADJUST button until OFF shows above. NOTE: Your salt monitor is an estimate of your salt level; accuracy depends on the type of salt used and other regeneration characteristics. SALT MONITOR SYSTEM The face plate timer has a low salt monitor with an indicator light to remind you to add salt to the storage tank. Lift the salt hole cover and level the salt in the storage tank. The salt level decal, on the brinewell inside the tank, has numbers from 0 to 8 (see Fig. Observe the number the leveled salt is at or closest to. Now, press the SALT LEVEL ADJUST button until black bars display up to the salt level number. For example, the figure shows the salt level at 6. Finally, set the level you want the low salt indicator light to come on. Press the SIGNAL LIGHT ADJUST button until a (*) shows opposite this number. In the example, the light will come on when the stored salt ADDING SALT TO STORAGE TANK The Salt Monitor System will turn the low salt light on to warn you when to refill with salt. Check for a low salt light a few weeks after you install the softener, and every week after that. Add salt at about the #2 salt monitor level. At this level, the tank is about 1/3 full. Never let the softener use all the salt before refilling. Without salt, you will soon have hard water. After filling, reset the Salt Monitor System. Note: You will have a loss in softening capacity and may get partly hard water if less than 10 inches (salt monitor level 2) of salt is in the storage tank. Questions?Call The Kenmore Water Line 1-800-426-9345 22 Faceplate Timer Features OPTIONAL SETTINGS: · SALT EFFICIENCY · CLEAN FEATURE · CLEAN FEATURE MINUTES · MAXIMUM DAYS BETWEEN REGENERATIONS · INTELLISOFT 97% FEATURE · 12 / 24 HOUR CLOCK 1. To set any of the following options, press and hold SELECT for 3 seconds until 000 shows in the display Then press once until the SALT EFFICIENCY display shows. Use the UP or DOWN buttons to change the ON / OFF displays. When this feature is ON, the unit will operate at salt efficiencies of 4000 grains of hardness per pound of salt or higher, which will reduce the softeners salt usage. (May recharge more often using smaller salt dosage and less water). [. . . ] 625. 383560 and 625. 393560 6 1 5 29 28 27 7 Rating Decal Location 8 26 25 24 23 22 9 10 11 12 13 21 20 18 14 17 19 16 15 Questions?Call The Kenmore Water Line 1-800-426-9345 42 Parts List Kenmore MODEL Nos. 1 1 2 3 -- 4 5 6 -- 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Part Number ------7284207 7284231 7284249 7275907 7288552 7284574 7284558 7284621 7265025 7219888 7082150 7003847 7100819 7137913 7287140 7284613 0900431 1103200 9003500 7239155 7105047 0502272 7287174 7170270 7077870 7170254 7170296 7141001 7176292 7088033 3442699 7287205 7282598 Part Description Cover Lock (Required for shipping only) Rim Insert (Required for shipping only) Cover (main) Salt Hole Cover (order following decal) Instruction Decal Transformer, 24V-10VA Timer Repl. (PWA) Faceplate (order following decal) Faceplate Decal Rim Ultra Cleansing Screen Brinewell Cover Wing Nut, 1/4" O-Ring Brinewell Decal, Salt Level Salt Storage Drum Plastic Screw, 1/4" x 5/8" Tube Clamp Tube Adaptor Grommet Brine Valve Assembly (also see pages 44 & 45) Replacement Distributor Resin Resin Tank (including Key No. [. . . ]