User manual KENMORE INSTALL-OF-SPECIALTY-SYSTEM

[. . . ] The Master Agreement: [] [] [] Expert Unlimited all covered "No-lemon" service service by our 12, 000 professional repair Protection Agreement Here's also helps extend what's included the Life of your new appliance. Covered product if four or more occur within twelve months [] [] [] Product fixed Annual replacement Preventiv 1-800-361-6665. Repairs, provides an annual =tenance Check, at your request, to 31iance is in proper For more running condition. Power surge due to power product takes You can call appointment Day or night, or schedule That's count years ment Some The life of your new purchase for your Master Protection Agree- SEWING 32 32 32 32 34 34 36 36 36 38 40 40 40 not related XlII to fundamental operations have been omitted from this manal. [. . . ] if the plug does not fit in the outlet , reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Sewn and lock stitches other pattern NOTE: You can sew a single unit of the selected you press the Auto-lock pattern if If you start sewing with the needle up, it wilt be up when you stop the machine. If you start sewing with the needle down. @_ odeelectioney Ms k Press button this toenter ofthe one following modes. [2] Stitch Down (_ NOTE: You can adjust the stitch width while the machine running. You can adjust the stitch length while the machine NOTE: running. Droppinghe Feed t Dog The dog belowered drop lever feed can bythe feed forsewing onbuttons, manual embroidery etc. Push drop lever right the feed tothe tolower feed the dog. Push thelever totheleftoraise feed itwill t the dog; Return to the up position when starting NOTE: The feed dog should be in up position sewing. The feed dog comes up after setting the lever in the up position, _ _ Down position Up position Turn OFF the power switch before changing the foot Always use the proper foot for the selected pattern. [i] Raise the presser foot and hold the needle thread with your fingers. Raise the needle to its highest Balancing hread T Tension Correct tension _ Needle (Top thread thread) _ Bobbin threadBottom ( thread) _ Toloosen _ Totighten The straight has ideal stitch threads lockedetween b two layers ffabric, o asillustrated. Ifyou atthe and took top bottom ofaseam, notice thathererenogaps. Thread Results depend on: - stiffness thickness fabric and ofthe - number offabric layers - type ofstitch Tension too tight is If the needle thread sh_ws through on the wrong side (Bottom side) of the fabric, and the stitch feels bumpy, turn the dial to a higher tension setting number to tighten the needle thread tension. Adjusting the needle thread tension for a zigzag stitch For an ideal zigzag stitch, the bobbin thread does not show on the right side (Top side) of the fabric and needle thread shows slightly on the wrong side (Bottom side) of the fabric. Wrong side (Bottom side) of the fabric without causing excessive puckering, or causing the bobbin thread to show on the right side (Top side) of the fabric. results vary with fabric , thread and sewing conditions. Tension is too tight _ Right side (Top side) of fabric _ Wrong side (Bottom side) of fabric The corner of each zigzag pulls together side of the fabric. The corner of each zigzag point pulls together wrong side of the fabric. Straight titchSewing S Machine setting 0_23_ 000 _) Pattern: _) LED display _) Foot: A:Zigzag foot Starting to sew Raise the presser foot and place the fabric on the machine. Lower the needle into the fabric where you want to start. [. . . ] Foot and draw the needle the hole on the foot. Place the fabric under the foot and lower the needle at the starting _ _ _ _ Buttonhole mark point. Make sure there is no gap between Spring holder, otherwise the left and right length of the buttonhole witt be different. (1) Step 1 and 2: Front bartack _2_ Starting point (2) Step 3: Right row (3) Step 4: Back bartack end _3b End point (4) LED shows each sewing when the buttonhole Dot If you try to set_ foot, the LEDdisp! [. . . ]