User manual KENWOOD 6708EP

[. . . ] Press the reset button. ¤ · Mounting and wiring this product requires skills and experience. For safety's sake, leave the mounting and wiring work to professionals. · Make sure to ground the unit to a negative 12V DC power supply. · Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. [. . . ] Also avoid places with too much dust or the possibility of water splashing. If you use the wrong screws, you could damage the unit. · If the power is not turned ON ("PROTECT" is displayed), the speaker wire may have a short-circuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked. · Make sure that all wire connections are securely made by inserting jacks until they lock completely. · If your vehicle's ignition does not have an ACC position, or if the ignition wire is connected to a power source with constant voltage such as a battery wire, the power will not be linked with the ignition (i. e. , it will not turn on and off along with the ignition). If you want to link the unit's power with the ignition, connect the ignition wire to a power source that can be turned on and off with the ignition key. · Use a commercially available conversion connector if the connector does not fit in the vehicle connector. · Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. Power control/ Motor antenna control wire (Blue/White) Mute wire (Brown) Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. If no connections are made, do not let the cable come out from the tab. 4| 6708EP/6708EPY/DDX52RY Cooling fan FM/AM antenna input (JASO) FUSE ( 15A ) Wiring harness (Accessory 1) REVERSE REMO. CONT MUTE ANT. CONT P CONT English | 5 Connecting Wires to Terminals Connector Function Guide Pin Numbers for ISO Connectors External Power Connector A-4 A-5 A-6 A-7 A-8 Speaker Connector B-1 B-2 B-3 B-4 B-5 B-6 B-7 B-8 Cable Colour Functions 2WARNING Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. Please be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles etc. Yellow Blue/White Orange/White Red Black Battery Power Control Dimmer Ignition (ACC) Earth (Ground) Connection Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Rear Right (+) Rear Right (­) Front Right (+) Front Right (­) Front Left (+) Front Left (­) Rear Left (+) Rear Left (­) 1 (Default setting) The A-7 pin of the vehicle's ISO connector is linked with the ignition, and the A-4 pin is connected to the constant power supply. Ignition cable (Red) Unit Battery cable (Yellow) A-4 Pin A-7 Pin Vehicle 2 The A-7 pin of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin is linked to the ignition. Ignition cable (Red) Unit Battery cable (Yellow) A-4 Pin A-7 Pin Vehicle 3 The A-4 pin of the vehicle's ISO connector is not connected to anything, while the A-7 pin is connected to the constant power supply (or both the A-7 and A-4 pins are connected to the constant power supply). Ignition cable (Red) Unit Battery cable (Yellow) A-4 Pin A-7 Pin Vehicle / · When the connection is made as in 3 above, the unit's power will not be linked to the ignition key. For that reason, always make sure to turn off the unit's power when the ignition is turned off. To link the unit's power to the ignition, connect the ignition cable (ACC. . . red) to a power source that can be turned on and off with the ignition key. 6| 6708EP/6708EPY/DDX52RY System Connection USB terminal USB device (commercially available) Do not connect. Audio Input Resistance-free stereo type mini plug Visual Input Resistance-free mini plug Rear View Camera Input · Visual input (Yellow) Audio/Visual Output · Visual output (Yellow) Front Preout · Audio left output (White) · Audio right output (Red) Rear Preout/ Subwoofer Preout · Audio left output (White) · Audio right output (Red) Audio/Visual Output · Audio left output (White) · Audio right output (Red) English | 7 Optional Accessory Connection iPod (commercially available) KCA-iP300V (Optional Accessory) Audio Output (Black) Visual Output (Yellow) Visual Input (Yellow) USB terminal USB terminal Navigation System (Optional Accessory) Audio Input (Black) KCA-BT200 input (Optional Accessory) TV Tuner (Optional Accessory) Connection cable (Included in the Navigation System) TO MONITOR UNIT TV ANTENNA INPUT Connection cable (Included in the TV tuner) 8| 6708EP/6708EPY/DDX52RY Installation for Monitor/Player Unit Firewall or metal support Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw (commercially available) Metal mounting strap (commercially available) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). Installing the Escutcheon Accessory 3 English | 9 Removing Monitor/Player Unit Removing the Hard Rubber Frame (escutcheon) 1. [. . . ] Self-tapping screw (commercially available) Metal mounting strap (commercially available) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). Installing the Escutcheon Accessory 3 English | 9 Removing Monitor/Player Unit Removing the Hard Rubber Frame (escutcheon) 1. Engage the catch pins on the removal tool 2 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Removal Tool (Accessory 2) Removing the Unit 1. [. . . ]